Intel MR 3108 ROC Hardware RAID Firmware 24.10.0-0017
Dosya tipi: Firmware.
Işleti̇m Si̇stemi: AnyOS.
Dosya adı: 3108-MR_FWPKG_v24.10.0-0017.zip.
Bit: 32/64 Bit.
Li̇sans: Ücretsiz.
Açıklama
sürümleri:
– Firmware 4.290.00-4536
– BIOS 6.28.04.0
– NVDATA 3.1507.00-0006
– UEFI_Driver 0x06110200(signed)
– Hii 03.17.14.00(signed)
– Ctrl-R 5.13-1100
– ROMENV 1.09
– BootBlock 3.07.00.00-0002
– FCODE 4.17.08.00
– PCLI 1.07.05
değişiklikler:
SCGCQ00718801 – (Closed) – FW breaks to MonTask: line 1168 in file ../../raid/raid.c during RAID Operations
SCGCQ00724451 – (Closed) – FW breaks to MonTask: line 889 in file ../../raid/bladeDMA.c while creating a filesystem on R5 VD.
SCGCQ00725844 – (Closed) – Intruder pre alpha 2 : On a R1 to R5 reconstructing Virtual Drive, IO failed with data miscompare
SCGCQ00729599 – (Closed) – Intruder pre alpha 2 : “MonTask: line 396 in file ../../ssd/ssd_cache_fw.c” with IO on R5 VD with a CacheCade VD in WB
SCGCQ00747258 – (Closed) – .10 PL cause DataTLB error with MR FW.
SCGCQ00751361 – (Closed) – 512e support needs to be enabled in MR FW
SCGCQ00788071 – (Closed) – Code review items were fixed
SCGCQ00788072 – (Closed) – Code Review fixes for review Review 38871 -Integrate 6.5 Changes with Intruder Code stream
SCGCQ00791766 – (Closed) – Rebase Dev stream with Integration 6.5 manual changes
SCGCQ00794871 – (Closed) – FW breaks to MonTask: line 257 in file ../../dm/src/dmDrvPrep.c when booting FPGA
SCGCQ00807498 – (Closed) – Data corruption detected with offload and restore operation
SCGCQ00812867 – (Closed) – Data corruption reported with Intruder ONFI2 offload and restore operation
SCGCQ00819772 – (Closed) – Flash wrongly discovered as transported across back to back offload and restore cycles
SCGCQ00822311 – (Closed) – ONFI unable to offload to controllers with multiple chipselects
SCGCQ00823817 – (Closed) – FPGA stream missing .4 release stream content
SCGCQ00831595 – (Closed) – FW hanging with 0.6 release while bootup.
SCGCQ00832908 – (Closed) – MSM displays error message if ‘Schedule Consistency Check’ is selected.
SCGCQ00843098 – (Closed) – Un-correctable ECC error on Armstong board during cold boot
SCGCQ00844777 – (Closed) – Modifying SBR PnP IDs offset
SCGCQ00845435 – (Closed) – Data Corruption on WB VDs
SCGCQ00846621 – (Closed) – Medium error correction events were not reported
SCGCQ00848339 – (Closed) – FW hangs during cache flush after restore cache from flash.
SCGCQ00850401 – (Closed) – ONFI: FC0 CS0 offload meta length not valid:0, expected:7c00 causing restore to not start after offload.
SCGCQ00850839 – (Closed) – FW hangs after re-inserting SATA drive in direct connect topology during I/O.
SCGCQ00856977 – (Closed) – Unable to update drive firmware on customer specific FDE SATA SSDs
SCGCQ00858697 – (Closed) – For Sugon Romb dont Initialize the port activity LED’s GPIO.
SCGCQ00863880 – (Closed) – MR_6.9_FW : Core 0 exception seen while trying to import foreign configuration with pinned cache present.
SCGCQ00864054 – (Closed) – Perform the PCI release retry while performing BISR on the second CPU.
SCGCQ00865116 – (Closed) – ROC Temp GPIO action item
SCGCQ00866261 – (Closed) – Invader firmware (4.280.00-4331 in MR 6.7) with write-verify has abnormal behavior/performance.
SCGCQ00867065 – (Closed) – Increase CACHE HEADER version, since new member was added to PinnedCacheDataStructure(Persistent DRAM)
SCGCQ00872875 – (Closed) – MR_6.9: MonTask: line 1280 in file ../../raid/1078dma.c. DCDB cmd timed out
SCGCQ00872889 – (Closed) – MR6.9_FW : Kill adapter seen while issuing Task Management in loop on 240 JBODs with IOs.
SCGCQ00873991 – (Closed) – Data TLB error occured after issuing task abort from host
SCGCQ00878414 – (Closed) – 6.9 : Write perf drops in 16R5 WT NoRA DCD SS64 1MB IO at QD128/256
SCGCQ00878432 – (Closed) – Blade DMA errors observed while running IOs
SCGCQ00878587 – (Closed) – MonTask: line 245 in file ../../raid/1078int.c while running I/Os with 64VDs and pull out drives belonging to CacheCade VD
SCGCQ00879193 – (Closed) – Restricting the VD deletion optimization to reduce IO freeze to least latency mode.
SCGCQ00881001 – (Closed) – StorCLI Reports Incorrect TFM Manufacturing Date
SCGCQ00881901 – (Closed) – FW hang, even-after Task Abort is successful on a drive in Linux OS
SCGCQ00882125 – (Closed) – On receiving CACHE_FLUSH_DCMD, set forceCacheflush flag to 1 to flush the cache
SCGCQ00882897 – (Closed) – Need to set perfTunerMode appropriately on controller reset.
SCGCQ00884589 – (Closed) – Windows BSOD when upgrade FW 24.6.0-0040 to 24.8.0-0026 with driver 6.707.08.00
SCGCQ00890133 – (Closed) – Invader 6.9: FW breaks MonTask: line 245 in file ../../raid/1078int.c with IOs on max VD configured and BGOps
SCGCQ00891924 – (Closed) – Buffer Size is set to 1M and number of BSB per BB is set to 1.
SCGCQ00893588 – (Closed) – MR6.9_FW : IO halts on JBODs with read/write error when the target drives are reset via MFI or MPT path on Linux distro
SCGCQ00895554 – (Closed) – MR_6.9_FW: Kill adapter during test run
SCGCQ00904905 – (Resolved) – Copyback fails to start and causes a FW fault
SCGCQ00717238 – (Closed) – MR Intruder Fault x6101 – FW breaks to Montask: line 1557 in file ../../dm/pl2/pliopi.c
SCGCQ00738085 – (Closed) – Change flags for each sge in the sglist.
SCGCQ00750804 – (Closed) – FW breaks to MonTask: line 299 in file ../../raid/1078int.c when try to run IO on 32 drive R0 16 VD configuration.
SCGCQ00771238 – (Closed) – remove Cache split related changes from Int stream
SCGCQ00788087 – (Closed) – Multi- SAS Core – Code reivew defect fixes.
SCGCQ00788526 – (Closed) – Defect to check in code changes reported by static analysis tool for intruder
SCGCQ00803219 – (Closed) – Data corruption when destaging pinned cache after foreign config import.
SCGCQ00812295 – (Closed) – Back to back restore happen because flash region not toggled after a restore operation
SCGCQ00819786 – (Closed) – FW should prepare and arm HW for second offload before starting cache flush
SCGCQ00836031 – (Closed) – NVDATA and Controller Properties all zero
SCGCQ00845921 – (Closed) – Development defect for Cache Offload work around.
SCGCQ00846655 – (Closed) – Battery relearn timed out on Supercap on Armstrong board
SCGCQ00847001 – (Closed) – MR6.6 Controller is not accessible through OOB before OS is up and running
SCGCQ00848264 – (Closed) – Development defect for flash chip M83C workaround in Intruder
SCGCQ00850368 – (Closed) – Firmware Faults with error code 0x22 after an OCR
SCGCQ00855837 – (Closed) – A race condition exists while creating the flash filesystem and making the corresponding entries in NVRAM
SCGCQ00855845 – (Closed) – Disable pause for memory offload control 1.
SCGCQ00857181 – (Closed) – On performing back to back target reset on the same JBOD results into online controller reset(OCR)
SCGCQ00857680 – (Closed) – MR 6.7 Point : Few test cases fail when PCIeCV tool is executed
SCGCQ00857692 – (Closed) – MR 6.9 : Firmware allows to perform Reconstruction when Pinned Cache is present.
SCGCQ00859850 – (Closed) – Pinned Cache lost after trigger few OCR and reboot server as result data got corrupt
SCGCQ00860066 – (Closed) – Firmware breaks to montask while importing the Foreign Config.
SCGCQ00860503 – (Closed) – MR 6.9 : Controller boots to OS Even when Pinned Cache is present and Boot Error handling is set to Stop on Error.
SCGCQ00860635 – (Closed) – Firmware hang is observed when Cache Offload is interrupted by power restore.
SCGCQ00860716 – (Closed) – Firmware allows to create more than 64 logical drives in legacy mode.
SCGCQ00861819 – (Closed) – Address code review defects for ER SCGCQ008554
SCGCQ00871973 – (Closed) – FW allows CCVD deletion with pinned windows
SCGCQ00873239 – (Closed) – FW downgrade fails with IOs and BGops .
SCGCQ00874200 – (Closed) – Re-eanbling 1MB IO support.
SCGCQ00878554 – (Closed) – Core 0 exception in line 245 in ../../raid/1078int.c while Target reset on PDs and BG Operations in parallel
SCGCQ00879198 – (Closed) – MR6.9_FW : Assertion failure in ../../dm/src/dmDrvPrep.c at line 836: while Cable pull push on secondary enclosure.
SCGCQ00882742 – (Closed) – Fix coverity defects
SCGCQ00886685 – (Closed) – Add sanity check for iPtr and rPtr after restore is completed.
SCGCQ00894472 – (Closed) – Adjust cache thresholds appropriately after the pinned cache is generated and volumes are retained in WB mode.
SCGCQ00894608 – (Closed) – OS become unresponsive after creating multiple sliced VD’s
SCGCQ00899762 – (Closed) – SKINNY compilation was broken after fixing SCGCQ00882125
SCGCQ00906129 – (Closed) – Intruder : Data Corruption issue seen while running cable breaker with CCVD associated
SCGCQ00908325 – (Closed) – Undoing the changes of CSET activity SCGCQ00803718
SCGCQ00914740 – (Closed) – 6.9: Default values does not get picked up for un-changed controller property sharing same byte.
SCGCQ00764924 – (Closed) – FW breaks to Montask: line 891 in file ../../raid/bladeDMA.c while creating file system on VDs.
SCGCQ00788106 – (Closed) – Code review fixes for 33080
SCGCQ00819441 – (Closed) – Port ONFI changes to Intruder .5 stream.
SCGCQ00823465 – (Closed) – Reconstruction from R1 to R5 causing FW hang.
SCGCQ00844839 – (Closed) – Armstrong board causing HP server to hang during bootup.
SCGCQ00845436 – (Closed) – Limit the Memory size to 1GB as temp workaround to DC issue.
SCGCQ00850220 – (Closed) – Check in OCR work around
SCGCQ00850441 – (Closed) – iMR 6.1.1 : Exception seen during OS Reboot heat run test
SCGCQ00850818 – (Closed) – Controller hangs during post if you have dirty cache that needs to be flushed to the VD.
SCGCQ00851267 – (Closed) – Firmware halted after trigger OCR with I/O
SCGCQ00852327 – (Closed) – When no drives connected tlb error is seen
SCGCQ00853020 – (Closed) – Firmware Test API returns incorrectly that hardware is armed for offload, when supercap is bad.
SCGCQ00855322 – (Closed) – !!! Firmware initialization failed. Fault code = 0x4 !!!
SCGCQ00857528 – (Closed) – MR_6.8:FW hits to MonTask: line 4946 in file ../../raid/ld.c while multipath push pull with patrol read
SCGCQ00859961 – (Closed) – Cannot disable patrol read on an Armstrong controller.
SCGCQ00865963 – (Closed) – Too many event in firmware log : onfiHwIsOffloadSustainableStateSet onfi_status 0
SCGCQ00872140 – (Closed) – MR6.9:’Watchdog Timer Exception’ followed by FW crash after initiating PD Erase on UG PD, with BG operation & IO’s on 64 VD’s
SCGCQ00873201 – (Closed) – Avoid cache FLUSH during VD Deletion to reduce IO Freeze time on other VDs
SCGCQ00874332 – (Closed) – MR6.9_FW : FW hits montask due to a non-spinning up FDE drive, issue seen on repeated reboots.
SCGCQ00880919 – (Closed) – MR6.9_FW : Controller discovery failed due to pending Boot messages, adapter at baseport not responding.
SCGCQ00886351 – (Closed) – MR 6.8 : Few test cases fail when PCIeCV tool is executed
SCGCQ00900250 – (Closed) – Send appropritate MFI status for the command which needs to be aborted
SCGCQ00827430 – (Closed) – Loss of smart recovery blocks in a small window when switching regions
SCGCQ00832205 – (Closed) – Development defect to fix Code Coverity issues found in Intruder 0.6 Stream.
SCGCQ00845707 – (Closed) – MSM reports 4MB and 8MB FW image is corrupt and does not allow flashing Armstrong board.
SCGCQ00846582 – (Closed) – SATA drives not detected in direct connect topology -MR
SCGCQ00846657 – (Closed) – ONFI offload descriptors are not set to offload all valid DATA cache
SCGCQ00859720 – (Closed) – On OCR or reboot, retain volumes in WB if the number of pinned buffers is less than 50% of available buffers.
SCGCQ00859975 – (Closed) – Code review defect with 6.9 merge with Inv team
SCGCQ00860140 – (Closed) – Coverity: fix Coverity defect 16729
SCGCQ00874357 – (Closed) – Data TLB error occured while tring dereference invalid command ID
SCGCQ00877673 – (Closed) – Kill adapter while running IO with Task Reset on JBODs
SCGCQ00878923 – (Closed) – Remove PinnedCacheDataStructure totalPinnedBbs and totalPinnedBsbs update in PinCacheForLd()
SCGCQ00881919 – (Closed) – Data TLB error found while running the target reset script with multipath cable pull-push operation
SCGCQ00848368 – (Closed) – Armstrong Controller hangs when make JBOD from powersave PD.
SCGCQ00848372 – (Closed) – API calls to corrupt and verify DIS on ONFI NAND flash are not available in Intruder code release
SCGCQ00856566 – (Closed) – Code review defect with 6.9 merge with Inv team
SCGCQ00866487 – (Closed) – MR6.9_FW : sasPortNumberValid bit does not get updated in CtrlR
SCGCQ00867120 – (Closed) – MR6.8_FW : DISM stuck at device discovery on enclosure power cycle, Devices present with DM but not reflected in upper layers
SCGCQ00869626 – (Closed) – Compilation Error in Invader with Intruder merged code
SCGCQ00878097 – (Closed) – MR6.9:Assertion failure in ../../raid/cache.c at line 774, after pulling out the enclosure cable
SCGCQ00864019 – (Closed) – One deletion of CCVD FW displays incorrect CCVD target id and remaining CacheCade size on the system
SCGCQ00878150 – (Closed) – Controller killed on issuing OCR from StorCLI after disabling it from OS.
SCGCQ00881005 – (Closed) – Code cleanup issues.
SCGCQ00848321 – (Closed) – Offload starting with residual power, which corrupts metadata
SCGCQ00849733 – (Closed) – Development defect to remove the hardcoded TFM VPD values in firmware for Intruder.
SCGCQ00863348 – (Closed) – Remove checkSysPwrStatus() and processSysPwrReturn() functions.
SCGCQ00866206 – (Closed) – Modify app.ld to address iopath and dramCode region overflow – MR 6.9Intruder
SCGCQ00869060 – (Closed) – Intruder6.9 code review changes
SCGCQ00877100 – (Closed) – TTY log dump is not persistent for multiple boots.
SCGCQ00848328 – (Closed) – L2 Cache Error was NOT detected at POST after inject ECC error
SCGCQ00859968 – (Resolved) – Deleting duplicate/unwanted files from source contr
SCGCQ00679021 – (Closed) – Bringup MR Intruder fpga with Init bit stream.
SCGCQ00681940 – (Closed) – Following FW interfaces are implemented
SCGCQ00696857 – (Closed) – Invader 6.3 GCA code ported to Invader stream
SCGCQ00713577 – (Closed) – 2.1b Bitstream related MR Fw changes for Dallas FPGA Validation.
SCGCQ00760455 – (Closed) – Integrate .12 PL into MR code
SCGCQ00772420 – (Closed) – Merge 6.5 Changes with Intruder Code stream
SCGCQ00791733 – (Closed) – New PL integrated.
SCGCQ00804452 – (Closed) – Integrate Latest PL .19 with MR stack
SCGCQ00813852 – (Closed) – PL 0.85 release check-in
SCGCQ00813853 – (Closed) – Flash header changes for Intruder
SCGCQ00814430 – (Closed) – Code bring up on 3108 controller
SCGCQ00817806 – (Closed) – Updating release script for Intruder code base
SCGCQ00827051 – (Closed) – Integrate .22 PL and Invader 6.7 code.
SCGCQ00827085 – (Closed) – Adding Support in Firmware for a new Flash Controller for Intruder.
SCGCQ00834328 – (Closed) – Enable Synchronous mode of communication between Intruder and Flash Chip.
SCGCQ00840256 – (Closed) – Code changes for A0 silicon & Eval board.
SCGCQ00842347 – (Closed) – Creation and productization of new product SKU for 9361-8i board with 2GB of memory
SCGCQ00844787 – (Closed) – support for dual rank ddr memory in Intruder, new pl library, and DMA workaround
SCGCQ00846939 – (Closed) – Re-branding effort for customer.
SCGCQ00850707 – (Closed) – Fault LED support for predictive failure drives for SGPIO
SCGCQ00855889 – (Closed) – OEM wants controller VPD reporting should be disable
SCGCQ00856088 – (Closed) – GPIO Settings for a customer
SCGCQ00861994 – (Closed) – Check-in 6.9 Intruder code changes to use same MEM_FIXED for Inruder and Invader
SCGCQ00864357 – (Closed) – Check-in PL 250.34 to Inruder A0.
SCGCQ00865372 – (Implemented) – Reduce Command Block Latency during Background Operations
SCGCQ00882016 – (Closed) – Integrating PL 06.00.05.00 with 6.6 FW stream.
SCGCQ00884951 – (Closed) – Integrate 08.00.05.00 MR PL with MR 6.8
SCGCQ00893029 – (Closed) – Add support to enable/Disable of Large IO Support – 1 MB IO
SCGCQ00908329 – (Closed) – SCSI Inquiry string should not change in current generation HBA
SCGCQ00681943 – (Closed) – ONFI debug functionality implemented to test software based offload and restore operations
SCGCQ00687251 – (Closed) – Implement Cache-split feature
SCGCQ00710266 – (Closed) – Intruder Dual SAS core changes.
SCGCQ00721312 – (Closed) – Add support for TM and Error handling with dual sas core to MR.
SCGCQ00772441 – (Closed) – Intergrate PL 0.13 to Intruder fpga
SCGCQ00772443 – (Closed) – Put Infrastructure to compile Intruder and Invader on same code base.
SCGCQ00792619 – (Closed) – Implemented as part of Intruder FPGA bringup.
SCGCQ00837210 – (Closed) – For the new flash chip in Intruder, additional DDR Regions is memset to 0 after cache restore is complete.
SCGCQ00841116 – (Closed) – Add Manual BISR to bring up secondary core for Intruder
SCGCQ00862035 – (Closed) – New LED to indicate Over Temperature in Intruder.
SCGCQ00809693 – (Closed) – Invader 6.6 Code stream merge to Intuder.
SCGCQ00852052 – (Closed) – Add pl 0.250.27 to Intruder code.
SCGCQ00853299 – (Closed) – Incorporate Memory Port difference for xor base address for Intruder
SCGCQ00853423 – (Closed) – Implement the HW workaround in Intruder to recover from warm reset
SCGCQ00855457 – (Implemented) – Task management support for JBOD/sysPD to Windows and Linux drivers (follow-on to PR SCGCQ00687438)
SCGCQ00860586 – (Closed) – Add 5/15 6.9 action item changes
SCGCQ00861695 – (Closed) – Add support for Micron M83C flash part for Intruder generation products.
SCGCQ00880731 – (Closed) – Integrate Phase 9 PL 9.0.0.0 with MR 6.9
SCGCQ00781019 – (Closed) – Retain Configuration btw boots on FPGA environment
SCGCQ00846602 – (Closed) – New GPIO definitions for Intruder
SCGCQ00868957 – (Closed) – Integrate Phase 9 PL (version 9.0.0.0) with MR 6.9
SCGCQ00841181 – (Closed) – A0 Intruder bring activities Part 2
SCGCQ00856859 – (Closed) – Check in new pl 250.32
SCGCQ00860624 – (Closed) – Update ManPage12 and ManPage13 as per new structures defined for Intruder
SCGCQ00852061 – (Closed) – MPIC configuration table changes
SCGCQ00852502 – (Implemented) – Avoid Moving WB volumes to WT on pinned cache genera
SCGCQ00805369 – (Port_Complete) – Bad physical drive caused controller error recovery go in loop
SCGCQ00833943 – (Port_Complete) – MR6.7-Beta:FW hits to MonTask: line 1272 in file ../../raid/1078dma.c after Injecting media error in loop on CCVD metadata
SCGCQ00833944 – (Port_Complete) – MR6.7-Beta:FW hits to MonTask: line 1272 in file ../../raid/1078dma.c after Injecting media error in loop on CCVD metadata
SCGCQ00833945 – (Port_Complete) – MR6.7-Beta:FW hits to MonTask: line 1272 in file ../../raid/1078dma.c after Injecting media error in loop on CCVD metadata
SCGCQ00833946 – (Port_Complete) – MR6.7-Beta:FW hits to MonTask: line 1272 in file ../../raid/1078dma.c after Injecting media error in loop on CCVD metadata
SCGCQ00837206 – (Port_Complete) – Setting the Learn Cycle property of iBBU09 gives an I2C error
SCGCQ00838545 – (Port_Complete) – MR_6.8_FW: Fw hits to MonTask: line 1272 in file ../../raid/1078dma.c while running IO in VM
SCGCQ00841545 – (Port_Complete) – Performing a cable pull/push with array property change resulting into FW hang.
SCGCQ00844445 – (Port_Complete) – Commands to the fde drives are not responding within 500ms.
SCGCQ00845203 – (Port_Complete) – MR_6.8_FW:Firmware halted and restarted while doing flash erase on the onfi flash
SCGCQ00848415 – (Port_Not_Required) – flush cache with write_verify on R0 volume and sata drive
SCGCQ00849553 – (Port_Complete) – Unexpected controller reset during test run
SCGCQ00849614 – (Port_Complete) – chain element for non RW commands were not pulled in the FW
SCGCQ00849620 – (Port_Complete) – Deleting a Cachecade VD (CC VD) results in a firmware hang situation.
SCGCQ00850990 – (Port_Complete) – Rebuild Performance for RAID 1 arrays is slower.
SCGCQ00851993 – (Port_Complete) – Patrol Read Properties window does not pop up on MSM
SCGCQ00853534 – (Port_Complete) – L2 unrecoverable cache error was seen during Patrol read properties modification in certain conditions.
SCGCQ00854160 – (Port_Complete) – Controller Reboots after doing an OCR with IOs running in the background
SCGCQ00854164 – (Port_Complete) – Controller cache fails to destage when multiple SVDs are present
SCGCQ00854165 – (Port_Complete) – Controller cache fails to destage when multiple SVDs are present
SCGCQ00854168 – (Port_Complete) – Controller cache fails to destage when multiple SVDs are present
SCGCQ00854169 – (Port_Complete) – Controller cache fails to destage when multiple SVDs are present
SCGCQ00854170 – (Port_Complete) – Controller cache fails to destage when multiple SVDs are present
SCGCQ00869785 – (Port_Complete) – Fault LED support for predictive failure drives for SGPIO
SCGCQ00873092 – (Port_Complete) – FW allows CCVD deletion with pinned windows
SCGCQ00873093 – (Port_Complete) – FW allows CCVD deletion with pinned windows
SCGCQ00873094 – (Port_Complete) – FW allows CCVD deletion with pinned windows
SCGCQ00878362 – (Port_Complete) – Code collab fixes delivered
SCGCQ00878401 – (Port_Complete) – Cleanup device wait queue if drive is no longer online
SCGCQ00882474 – (Port_Complete) – Disable FLR support in MR FW to address VMware guest VM abrupt shutdown issue
SCGCQ00886272 – (Port_Complete) – Windows BSOD when upgrade FW 24.6.0-0040 to 24.8.0-0026 with driver 6.707.08.00
SCGCQ00886665 – (Port_Complete) – disableImmediateIO is not reflected in FW
SCGCQ00886666 – (Port_Complete) – disableImmediateIO is not reflected in FW
SCGCQ00886826 – (Port_Complete) – Need to set perfTunerMode appropriately on controller reset.
SCGCQ00889407 – (Port_Complete) – MonTask: line 245 in file ../../raid/1078int.c while running I/Os with 64VDs and pull out drives belonging to CacheCade VD
SCGCQ00889884 – (Port_Complete) – MonTask: line 245 in file ../../raid/1078int.c while running I/Os with 64VDs and pull out drives belonging to CacheCade VD
SCGCQ00891282 – (Port_Complete) – Recon VD made “degraded” when the recon pd is pulled out allowing for rebuild once the drive is plugged back in.
SCGCQ00891288 – (Port_Complete) – Cisco – Colusa1 MonTask after Initiating a Raid Level migration
SCGCQ00908121 – (Port_Complete) – on creating 240VD and rebooting the server, FW breaks into montask.
SCGCQ00908153 – (Port_Complete) – LUID gets changed during foreing import from non-240VD FW to 240VD FW
SCGCQ00914823 – (Port_Complete) – Created VD configuration with PDs released from previous VD erased will lost after next reboot
SCGCQ00803718 – (Port_Complete) – Ctrl-r and HII does not show proper message when you try to import the 65th VD.
SCGCQ00838560 – (Port_Complete) – MR6.8_FW : Unable to Convert a JBOD PD to UG in Solaris
SCGCQ00843936 – (Port_Complete) – Handling Functional Level Reset (FLR) .
SCGCQ00844446 – (Port_Complete) – Enable I2C clock frequency of 100kHz for specific OEM is not working accurately
SCGCQ00844447 – (Port_Complete) – Handle enabling disk “write” cache setting from OS for OEM
SCGCQ00846479 – (Port_Complete) – Secure Erase on SATA SSD via CtrR or HII leads to unresponsive application, Secure erase failing intermittently
SCGCQ00849580 – (Port_Complete) – Failed to import iMR RAID configuration to 12G MR
SCGCQ00850924 – (Port_Complete) – MR & iMR FW Work-around is required for 3×08 chip Errata ID – 2012-RC714 for PCIE 3.0 compliance
SCGCQ00853537 – (Port_Not_Required) – L2 unrecoverable cache error was seen during Patrol read properties modification in certain conditions.
SCGCQ00854177 – (Port_Complete) – Vd erase does not resume after reboot in the presence of CCVD
SCGCQ00871400 – (Port_Complete) – Fault LED support for predictive failure drives for SGPIO
SCGCQ00886271 – (Port_Complete) – Windows BSOD when upgrade FW 24.6.0-0040 to 24.8.0-0026 with driver 6.707.0
SCGCQ00887602 – (Port_Complete) – MR 6.8 : Few test cases fail when Intel PCIeCV tool is executed
SCGCQ00895459 – (Port_Complete) – Removal of “LdDcmd return pinned list 0” spam in FW logs.
SCGCQ00844068 – (Port_Complete) – iMR:6.5-Exception in core 0 is seen when drives are spun down and an ocr is triggered
SCGCQ00844152 – (Port_Complete) – FW doesn’t poll all temp sensor channels every 5 seconds
SCGCQ00853147 – (Port_Complete) – Continuous “TASK_ABORT_INTERNAL” prints observed in FW, after running heavy IO’s on JBOD configured using 12Gig SAS SSD
SCGCQ00868527 – (Port_Complete) – MR 6.9 : Controller boots to OS Even when Pinned Cache is present and Boot Error handling is set to Stop on Error.
SCGCQ00870846 – (Port_Complete) – FW unable to detect the inserted drives
SCGCQ00876154 – (Port_Complete) – SAS and SATA HDD R0 and R10 1M performance regressions (-15% to -35%) at QD16 to QD256
SCGCQ00882149 – (Port_Complete) – StorCLI reports success on 4MB MR FW package flashing on iMR only controller.
SCGCQ00884719 – (Port_Complete) – ‘Fw initializing devices’ hangs on controller with specific failed drives on backplane
SCGCQ00891273 – (Port_Complete) – Megaraid Thunderbolt controller reports cache memory size as 0 when no logical drives are present.
SCGCQ00841533 – (Port_Complete) – Instruction TLB error seen when auto configuration command exectued from CLI application
SCGCQ00843390 – (Port_Complete) – Megaraid-sas driver hang with Falcon card
SCGCQ00851886 – (Port_Complete) – MSM displays error message if ‘Schedule Consistency Check’ is selected.
SCGCQ00892136 – (Port_Complete) – MR 6.6.3 “storcli /c0 show all” shows lot of bad block messages in the log
SCGCQ00835227 – (Port_Complete) – STASH firmware entered fault state with SSD drive
SCGCQ00872263 – (Port_Complete) – Fw crash and BIOS RSODs when VD1 deleted with recon on a PI VD(VD2) and Slow init on VD3.
SCGCQ00841772 – (Port_Complete) – MR firmware reports no smart error when attaching a PFA drive
SCGCQ00876142 – (Port_Complete) – FW unable to detect the inserted dr
SCGCQ00879731 – (Closed) – Legacy OpROM: Handle the conditions for battery failed state as per the Battery design do
SCGCQ00882729 – (Closed) – Legacy OpROM: Controller POST shows JBOD found on host adapter, when number of INT13 device is > deviceExposure
SCGCQ00866982 – (Closed) – Legacy OpROM: Overlapping seen in POST in presence of two controllers and foreign config during CTRL-H laun
SCGCQ00834718 – (Closed) – PNPs and support for 16 port 12G designs
SCGCQ00898506 – (Closed) – OS doesn’t boot after installing OS on the 100th VD , while having 240 VDs created in EFI mod
SCGCQ00834720 – (Closed) – PNPs and support for 16 port 12G designs
SCGCQ00844774 – (Closed) – Handle coverity defects
SCGCQ00880737 – (Closed) – Handled the coverity defects.
SCGCQ00892931 – (Closed) – Not able to set Controller properties
SCGCQ00896827 – (Closed) – Cannot convert the state of drive from JBOD to UG if the drive is not 16byte CDB
SCGCQ00825741 – (Closed) – UEFI Driver: Compilation error when debug Flags are enabled
SCGCQ00852480 – (Closed) – “Question value mismatch type!Press Enter” message is displayed while entering create virtual drive page
SCGCQ00878350 – (Closed) – HII Enclosure Management form multiple time navigation results in hang/multiple entries of enclosure seen
SCGCQ00879673 – (Closed) – HII: Add GUID check for bootable drive
SCGCQ00894460 – (Closed) – Controller status inconsistency between Dashboard and Controller management in HII
SCGCQ00915093 – (Closed) – HII: Updating LargeIOSupport as per the new API changes
SCGCQ00870398 – (Closed) – Incomplete Port enumeration i.e connector information is displayed for ESM and PD’s in HII
SCGCQ00873973 – (Closed) – Profile Based DHS creation grayed out
SCGCQ00879726 – (Closed) – HII: Handle the conditions for battery failed state as per the Battery design doc
SCGCQ00889780 – (Closed) – HII: Address review comments
SCGCQ00903490 – (Closed) – HII RLM for only R0 available when 18 or more drives are present
SCGCQ00860564 – (Closed) – In Make UG warning message OS JBOD drives are not listed
SCGCQ00898506 – (Closed) – OS doesn’t boot after installing OS on the 100th VD , while having 240 VDs created in EFI mode
SCGCQ00881426 – (Closed) – VD properties does not display Emulation type.
SCGCQ00893928 – (Closed) – HII: Address review comment
SCGCQ00834719 – (Implemented) – PNPs and support for 16 port 12G designs
SCGCQ00834720 – (Closed) – PNPs and support for 16 port 12G designs
SCGCQ00844917 – (Implemented) – OEM requesting to do a WRITE VERIFY prior to flushing cache. This needs to be managed via CLI
SCGCQ00893152 – (Closed) – HII: Add support to enable/Disable of Large IO Support
SCGCQ00828031 – (Implemented) – Add support to detect that an OS is installed on a JBOD
SCGCQ00854621 – (Closed) – Provide a more descriptive port enumerati
SCGCQ00888846 – (Port_Complete) – HII: Spelling mistakes in strings
SCGCQ00893220 – (Port_Complete) – Inconsistency in showing controller status between MSM and HII for Fake Flash errors
SCGCQ00865978 – (Port_Complete) – Pause for Password at boot time Enable/Disbale based on Boot Mode
SCGCQ00878512 – (Port_Complete) – HII-VD renaming truncates 15th character & allows for 16 characters,though only 15 supported
SCGCQ00882762 – (Port_Complete) – “Question value mismatch type!Press Enter” message is displayed while entering create virtual drive page
SCGCQ00884560 – (Port_Complete) – 13G Exception Screen thrown in uEFI environm
SCGCQ00873155 – (Closed) – Ctrl-R:Not able to lauch ctrl-R if 2 controllers, one with huawei and another with generic PnP ID is present.
SCGCQ00871350 – (Closed) – Handled the coverity defects.
SCGCQ00837424 – (Closed) – Storcli reports cache type as ‘RW’ instead of ‘R’ after R1 CC VD is degraded
SCGCQ00855701 – (Closed) – StorCLI does not find enclosures in multipath environment
SCGCQ00869436 – (Closed) – Include Partition table and GPT GUID check to detect OS/FS
SCGCQ00892967 – (Resolved) – Intruder: The size of the foreign config shown does not match with that after an import.
SCGCQ00893032 – (Closed) – With Liberator the Physical sector size of 512E drive is shown wrong
SCGCQ00853268 – (Resolved) – In EFI, Storcli displaying Bus Number ,Device Number and Function Number = 0 for all the controllers.
SCGCQ00868215 – (Closed) – Connector name field is displayed as & port 4-7 when a single ESM is connected in Multipath
SCGCQ00864200 – (Closed) – Checking in fix for resource leak
SCGCQ00867569 – (Closed) – storcli /c0 vall show is not listing CaC column when CC is not supported and displaying sCC with wrong value.
SCGCQ00870485 – (Closed) – EFI storcli is not working with intruder
SCGCQ00880534 – (Closed) – Invader 6.9 : Efi cli – Command fails with a hang when multiple controllers connected .
SCGCQ00860461 – (Closed) – In JBOD warning message all the drives are getting listed
SCGCQ00881720 – (Closed) – Foreign Config pop up scrollup/down does not respond
SCGCQ00860056 – (Closed) – “storcli show” shows wrong count for aso.
SCGCQ00868198 – (Closed) – Removing Phy information from Enclosure PD details.
SCGCQ00874381 – (Closed) – StorCLI: Memory Leak in function _available_memory_calc1.
SCGCQ00876796 – (Closed) – null pointer dereference
SCGCQ00892129 – (Resolved) – Most of the commands fail with “Invalid argument” error.
SCGCQ00884910 – (Closed) – StorCli Libmods 6.9 coverity fixes
SCGCQ00865108 – (Closed) – Ventura: storcli add vd fails with NVMe
SCGCQ00883409 – (Closed) – Storcli shows the wrong position of enclosures when they are connected in daisy chain with controller
SCGCQ00899384 – (Closed) – Buffer is not incremented when reading sector of the drive
SCGCQ00915164 – (Closed) – CTRL-H: Updating LargeIOSupport as per the new API changes
SCGCQ00889924 – (Closed) – Intruder Port2 and Port3 display are not handled in PD Mngt
SCGCQ00889771 – (Closed) – CTRL-H:Address Review comments
SCGCQ00881936 – (Closed) – Ctrl-R doesnot show the controller name above the menu
SCGCQ00850607 – (Closed) – added new command /c0 show swalilog equivalent to adpalilog
SCGCQ00834721 – (Implemented) – PNPs and support for 16 port 12G designs
SCGCQ00854633 – (Implemented) – Add details of pending FW images to StorCLI/sho adpinfo
SCGCQ00859740 – (Implemented) – RRB 88: Provide a more descriptive port enumeration (Libmods changes)
SCGCQ00893498 – (Closed) – LibMods: Add support to enable/Disable of Large IO Support – 1 MB IO
SCGCQ00893153 – (Closed) – CTRL-H: Add support to enable/Disable of Large IO Support
SCGCQ00854622 – (Closed) – Provide a more descriptive port enumeration
SCGCQ00850636 – (Closed) – Added support for flashing the FW on intruder and new Dev-ID’s of Invader are added for EFI.
SCGCQ00828032 – (Implemented) – Add support to detect that an OS is installed on a JBOD
SCGCQ00853218 – (Implemented) – Add support to detect that an OS is installed on a JBOD
SCGCQ00844918 – (Implemented) – OEM requesting to do a WRITE VERIFY prior to flushing cache. This needs to be managed via CLI
SCGCQ00854626 – (Closed) – Provide a more descriptive port enumera
SCGCQ00904852 – (Port_Complete) – Checking-in changes for defect-SCGCQ00904794
SCGCQ00857695 – (Port_Complete) – Consistent Sorting of Controllers for End Users in Customer Facing Tools (EFI storcli)
SCGCQ00873795 – (Port_Complete) – CTRL-H: MonTask – line 243 in file ../../raid/1078int.c during rebuild
SCGCQ00854296 – (Port_Complete) – Add Pause For Password feature in CTRLH
SCGCQ00853654 – (Port_Complete) – Libmods implementation for WRITE VERIFY prior to flushing cache.
SCGCQ00878517 – (Port_Complete) – CTLR_R: PI-DG : After break mirror, data protection shown as “NA”
SCGCQ00900172 – (Port_Complete) – Added the iMR cutlass PNP id’s(0x1000/0052h, 0x1000/0x0053h) to EFI controller explorer class.
SCGCQ00901264 – (Port_Complete) – MR 6.8: storcli reports legacy driver version when native driver is loaded for a Fury controller in ESXi 6.0
SCGCQ00853586 – (Port_Complete) – Get and Set Factory settings Failure
SCGCQ00850019 – (Port_Complete) – storcli /c0/eall/sall show smart command gives all zeros in the output
SCGCQ00849728 – (Port_Complete) – LibMOD:OEM requesting to do a WRITE VERIFY prior to flushing cache.
SCGCQ00878555 – (Port_Complete) – Ctrl-R is creating a smaller VD than specified when selecting a VD size in TB
SCGCQ00867486 – (Port_Complete) – Changed the Message for Hiding Boot VD Operation Status as per FW return error status.
SCGCQ00854279 – (Port_Complete) – Add Pause For Password feature in CTRLH
SCGCQ00893015 – (Port_Complete) – Inconsistency in showing controller status between MSM and Ctrl-R for Fake Flash errors
SCGCQ00874679 – (Port_Complete) – storcli doesnt display E252/E253 enclosure info on an 84016
SCGCQ00894487 – (Port_Complete) – Inconsistency in showing controller status between MSM and StorCLI for Fake Flash errors
SCGCQ00841286 – (Port_Complete) – Storcli : The bus error message is displaying for storcli /c0/eall/sall show smart comm
Bu indirme aşağıda listelenen ürünler için geçerlidir:
– Intel Integrated RAID Module RMS3CC040
– Intel Integrated RAID Module RMS3CC080
– Intel RAID Controller RS3DC040
– Intel RAID Controller RS3DC080
– Intel RAID Controller RS3MC044
– Intel RAID Controller RS3SC008
İndirme