Intel NUC RST Preinstall Sürücüsü 14.6.0.1029
Dosya tipi: Sürücüsü.
Işleti̇m Si̇stemi: Windows 10, Windows 7, Windows 8, Windows 8.1.
Dosya adı: f6flpy-x86.zip.
Bit: 32/64 Bit.
Li̇sans: Ücretsiz.
Açıklama
Resolved Issues:
– BSoD 0x154 when run S4
– IAStorUI has stopped working” when click ‘Manager’ tab (Unit with M2 PCIe SSD) with no empty port available
– BSOD/Hung observed while resuming from CS with PCIe AHCI drives in remapped state
– Trim doesn’t work on RAID0 on SATA SSD disks
– Recovery volume can’t be built in IRST when the secondary hard drives size is the same as the prim
– BSOD 0x9F occurred as reboot system after finishing Burn-in tool (4 hours) (add HDD R/W loading) test
– Cannot create RAID/SRT when RTD3 is enabled in BIOS
– SCSI Compliance Test 2.0 fails with NVMe disks
– Extremely low performance during copying file to RAID volume with PCIe AHCI
– RAID 1 going into ‘failed’ state during copying files to the volume.
Bu indirme aşağıda listelenen ürünler için geçerlidir:
– Intel NUC Board D34010WYB
– Intel NUC Board D54250WYB
– Intel NUC Board NUC5i3MYBE
– Intel NUC Board NUC5i5MYBE
– Intel NUC Kit D34010WYK
– Intel NUC Kit D54250WYK
– Intel NUC Kit NUC5i3MYHE
– Intel NUC Kit NUC5i3RYH
– Intel NUC Kit NUC5i3RYK
– Intel NUC Kit NUC5i5MYHE
– Intel NUC Kit NUC5i5RYH
– Intel NUC Kit NUC5i5RYK
– Intel NUC Kit NUC5i7RYH
Notes:
– Known Issue is defined as a potential RST issue that has been replicated internally by the Rapid Storage Technology team but has not been root caused to be an RST defect.
– The RAID OROM & UEFI version for this release is 14.6.0.2285, the driver and user interface version is 14.6.0.1029. The Devslp tool is posted under the CLI tool components on VIP kit.
– RST 14.6 release enables support for new platforms & features (includes legacy support for platforms and features supported in RST 14.5): Skylake mobile U/Y Corporate Platform, SKL-U 2+3e Platform and Desteği NVMe API
– Issue with detecting PCIe storage when remapping is enabled on HM170/QM170 is fixed with the Pre-OS build 14.6.0.2285 included with PV package.
– No RST support for PCIe storage devices in AHCI mode.
Known Issues:
– If use HDD larger than 1.3TB build recovery without show an error message when CSM disable.
– Intel RST driver v14.5.0.1059 cause BSOD Critical_Process_DIED during Sx
– BSOD 7E caused by iaStorA during cold boot stress test
– [Win10] SRT mode change to Enhanced, after setting Maximized mode and reboot PC.
– S4 hang black screen with certain NAS HDD under 2DR0 / 3DR5
– Error message display when run NvCacheScripts
– Removing the lowest numbered driver causes BSOD.
– RAID0 created using legacy OROM missing metadata on one of the drives
– PCIe NVMe SSD 2DR0 (2-disk RAID 0) performance lower than pass-through single SSD
– [RCfgSata][DOS] Partition table is not preserved when using the /U switch
– [RCfgsata][EFI][DOS]Incomplete serial number of drives is output when using the /ST switch
– [RST EFI CLI] EFI CLI config disk status does not show system disk information
– [rcfgsata.efi][SKL] Cannot boot to OS after creating RAID1 out of two data drives while preserving an MBR partition table
– DevSlpRegEditTool creates reg keys with invalid disk product_id
– rstcli.exe, rstcli64.exe allow to create recovery volume consisted of SATA and NVMe disks
– OS Spindown of matrix RAID volumes causes hang
İndirme