D-Link DSR-1000N rev.A1 Wireless Router Firmware 1.09B38 WW
Dosya tipi: Firmware.
Işleti̇m Si̇stemi: AnyOS.
Dosya adı: DSR-500N_FIRMWARE_1.09B38.ZIP.
Bit: 32/64 Bit.
Li̇sans: Ücretsiz.
Açıklama
New Features:
1. L2TP client mode enhancements: support MPPE and demand dialing.
2. User DB enhancements: support PPTP/L2TP tunnels external authentication though AD, LDAP and POP3.
3. Bridge mode enhancements: support QoS and firewall rules.
4. Spillover mode enhancements: both WAN1 and WAN2 will respond requests, e.g. ICMP, IPSec, etc., from Internet even when spillover threshold is not triggered.
5. PPTP VPN enhancements: allow PPTP severs to assign remote clients the same subnet as the local LAN.
6. Russia Dual Access enhancements: allow users to designate the outbound interface for IGMP control packets.
7. Web GUI enhancements: support auto parameters fill-out in the DHCP server configuration page.
8. CLI enhancements: support the “space” character.
9. More 3G dongle supports: add D-Link DWM-156 A7, D-Link DWM-157 B1, and D-Link DWM-158 D1, HUAWEI E303.
10. A new click button to quickly download Dbglogs.
11. A new checkbox to enable/disable auto config backup.
12. A new checkbox to enable/disable config file encryption.
13. Support a Windows-based config viewer for encrypted config files.
Problems Fixed:
1. WAN failure detection issues: DSR can’t allow using a ping-detecting server that is not in the same subnet as gateway.(DEUR20121116000011)
2. After delete IPsec one to one mapping rule, it could not drop the IPsec
tunnel from DSR Web GUI.
3. After delete the IPsec one to one mapping rule, local PC is still able to ping
remote PC with mapping IP address.
4. While changing the local network in IPsec policy, web GUI will display
incorrect message.
5. The CLI: security firewall ipv6 configure/edit doesn’t work.
Firmware Update Steps
Do NOT upgrade firmware on any D-Link product over a wireless connection. Failure of the device may result. Use only hard-wired LAN network connections.
1. Save the current routers configuration to file. Tools/System. (Note that reloading this onto new major version of firmware can cause problems and thus is recommended to configure the router from scratch. Do not load the old configuration file from the old major version. If you’re upgrading from minor to minor version, reloading of the configuration file shouldn’t cause a problem. In these cases, please do not upload the previous older configuration file, rather set up the router from scratch. Should you need the configuration information from the previous saved configuration file, capture, copy or write down all required information from the configuration file loaded on the router BEFORE applying the newer firmware update.)
NOTE:
For routers using the new web page UI:
Management -> System Admin -> System
Save Settings To Local Hard Drive
2. Factory reset the router using the routers web page Tools/System, is easiest, or the back button.
3. Update the router using the routers web page Tools/System using the .bin file(s) that was downloaded for your product model. The .bin files have to be unpacked from the .zip file.
4. After the router as updated and status has reported it was successful on the routers web page, power OFF the ISP modem/ONT for 30 seconds then power back ON the modem/ONT. Perform one more Factory reset of the router using the routers web page Tools/System.
5. After the router has reset and come back to ready, reload the saved configuration file or reconfigure the router from scratch and walk thru the set up wizard. Status LEDs should be Blue, Green or White for power and internet (Globe) the router unit depending on model.
NOTE:
Clear all browser caches before and after loading FW files.
Önemli notlar:
1. DSR-500AC/1000AC product doesn’t support BGP routing and are not affected by the potential vulnerability that is well known as CVE-2004-0230, the attacker can potentially reset the BGP connection with the device.
2. All DSR routers with WW version are not allowed to install RU firmware image in order to prevent unnecessary misunderstanding for customers.
3. Before plug DWM-152/156 3G USB dongle in DSR-500AC/1000AC, please make sure the SIM Card is not set PIN code.
4. Microsoft Windows XP has some well-known limitation to access USB storage of DSR router, D-Link provides a Registry Script file named: WinXP.reg which can solve limitation of Windows XP environment. Without applying this script file, it cannot copy file from Windows XP to USB storage. (This issue will not happen when copy file from USB storage to Windows XP)
5. For any firmware downgrade situation, i.e. from a newer version to an older one, it will take more time to restart system comparing to firmware upgrade, i.e. from an older version to a newer one. If you MUST execute firmware downgrade for your own reasons, please allow DSR more time to reboot system.
6. To authenticate SSL VPN users through external databases including RADIUS, LDAP, AD and POP3, admin must also need to create user accounts with the same username and password in the local user database.
İndirme