Buffalo TS3400R NAS Firmware 1.50
Dosya tipi: Firmware.
Işleti̇m Si̇stemi: Windows 10, Windows 7, Windows 8, Windows 8.1, Windows Server 2003, Windows Server 2008, Windows Server 2012, Windows Vista, Windows XP.
Dosya adı: ts3000-v150.zip.
Bit: 64 Bit.
Li̇sans: Ücretsiz.
Açıklama
Added and Modified Features:
– [SNMP]: Modified to support SNMPv3.
– [SNMP]: Modified to support the following settings that can be acquired via SNMP protocol: Model name, Firmware version, Serial number, Checking whether new firmware is available, Showing whether the function status is enabled or disabled, and S.M.A.R.T. for each drive
– [SNMP]: Update the MIB file on your SNMP client software to the latest version. You can download the MIB file from the Buffalo website.
– [OpenSSL]: Updated OpenSSL to the latest version.
– [Email Notifications]: Modified so that the report categories and when the email will be sent are now configurable. The current settings will be taken over by the firmware update but we recommend verifying if the function works properly after the firmware update.
– [Email Notifications]: S.M.A.R.T information is now available to be sent via the notification email. It can be configured from “Advanced Report Settings”.
Bug Düzeltmeler:
– [Failover]: Fixed a bug where failover could not be canceled temporarily if the online update notice is present.
– [Email Notification]: Fixed a bug where the authentication settings were kept even if the authentication was disabled.
– [UPS Sync]: Fixed a bug where the E10 error occurred when specific settings were changed without connecting the UPS to the TeraStation.
– [Settings]: Fixed a bug where Settings could not be accessed.
– [Settings]: Fixed a bug where the status of spare drive shows an error during bootup.
– [Settings]: Fixed a bug where the CPU became overloaded when a test email was sent with the wrong settings.
– [USB Drive]: Fixed a bug where files that contain 2-byte characters in the filename could not be accessed when they were stored in NTFS-formatted USB drives.
– [Samba]: Fixed a bug where the access-restricted folder reserved for admin users cannot be accessed after initializing settings.
Caution:
– Please consult your local technical support representative if you experience any problems caused by this firmware update.
– Do not turn the unit off until the update is finished. It will take several minutes. You will receive a message when the update is finished.
– USB drives are not mounted automatically after a firmware update. To mount them, unplug and then reconnect them.
How to Use the Updater:
1. Connect the TeraStation properly and configure the TeraStation and a computer to run the updater on the same network subnet. The subnet masks should be the same and the first three numbers of the IP addresses should be the same. The last number of the IP addresses should be different.
For example, if the IP address and subnet mask of the computer are
” 192.168.0.10 , 255.255.255.0 “
and the IP address and subnet mask of the TeraStation are
” 192.168.1.150 , 255.255.255.0 “
then the updater will _not_ work properly.
In this case, reconfigure the TeraStation’s IP address and subnet mask to
” 192.168.0.150 , 255.255.255.0 “.
Then they will be on the same subnet and the updater will work properly.
2. Close all applications. Also, stop or exit any firewall software.
3. Extract the downloaded file and run “TSUpdater.exe”. When a TeraStation is detected, an update window will open.
4. Select the TeraStation to update if multiple TeraStation are connected.
5. Click “Update” and enter the TeraStation’s admin password.
6. Click “OK”.
7. Transferring and updating the firmware will start. Wait until it finishes. The info LED will blink during the update.
8. When the update finishes, a message will be displayed.
İndirme