MikroTik RouterOS TILE Firmware 6.43 RC 56
Tipo de arquivo: Firmware.
Sistema operacional: AnyOS.
Nome do arquivo: all_packages-tile-6.43rc56.zip.
Bit: 32/64 Bit.
Licença: Grátis.
Descrição
MAJOR CHANGES IN v6.43:
– api – changed authentication process;
– backup – do not encrypt backup file unless password is provided;
– btest – requires at least v6.43 Bandwidth Test client when connecting to v6.43 or later version server except when authentication is not required;
– cloud – added IPv6 support;
– cloud – added support for licensed CHR instances (including trial);
– cloud – reworked “/ip cloud ddns-enabled” implementation (suggested to disable service and re-enable after installation process);
– mac-telnet – require at least v6.43 MAC Telnet client when connecting to v6.43 or later version server;
– radius – use MS-CHAPv2 for “login” service authentication;
– romon – require at least v6.43 RoMON agent when connecting to v6.43 or later RoMON client device;
– webfig – improved authentication process;
– winbox – improved authentication process excluding man-in-the-middle possibility;
– winbox – minimal required version is v3.15;
Alterações nesta versão:
– bridge – added support for BPDU Guard (CLI only);
– bridge – added support for DHCP Option 82 (disables hardware offloading, CLI only);
– bridge – added support for DHCP Snooping (disables hardware offloading, CLI only);
– bridge – forward LACPDUs when “protocol-mode=none”;
– bridge – improved packet handling;
– cloud – added simultaneous IPv4/IPv6 support;
– console – added “dont-require-permissions” parameter for scripts;
– dhcpv4-relay – fixed false invalid flag presence;
– dhcpv6-server – do not allow to run DHCPv6 server on slave interface;
– dhcpv6-server – fixed dynamic simple queue creation for RADIUS bindings;
– dhcpv6-server – properly update interface for dynamic DHCPv6 servers;
– ethernet – fixed possible link flaps after disabling/enabling the interface (introduced in v6.43rc51);
– ethernet – improved large packet handling on ARM devices with wireless;
– ethernet – removed obsolete slave flag from “/interface vlan” menu;
– hotspot – fixed customized HTML file usage (introduced in 6.43rc47);
– ike1 – zero out reserved bytes in NAT-OA payload;
– ike2 – fixed initiator first policy selection;
– ippool – improved used address error message;
– ipsec – added warning messages for incorrect peer configuration;
– ipsec – separate phase1 proposal configuration from peer menu;
– ppp – fixed interface enabling after a while if none of them where active;
– ppp – improved modem mode switching;
– snmp – added “temp-exception” trap;
– switch – fixed possible switch chip hangs after initialization on MediaTek and Atheros8327 switch chips;
– tile – fixed false HW offloading flag for MPLS;
– tr069-client – allow editing of “provisioning-code” attribute (CLI only);
– tr069-client – fixed unresponsive tr069 service when blackhole route is present;
– upgrade – fixed RouterOS upgrade process from RouterOS v5;
– ups – improved UPS serial parsing stability;
– w60g – general stability and performance improvements;
– w60g – stop doing distance measurements after first successful measurement;
– winbox – added “default-route-distance” parameter for “IPv6/DHCP-client” menu;
– winbox – fixed “sfp-connector-type” value presence under “Interface/Ethernet”;
– winbox – fixed warning presence for “IP/IPsec/Peers” menu;
– winbox – fixed “write-sect-since-reboot” value presence under “System/Resources”;
– winbox – show “System/RouterBOARD/Mode Button” on devices that has such feature;
– wireless – added option to disable PMKID for WPA2 (CLI only);
– wireless – fixed memory leak when performing wireless scan on ARM;
– wireless – updated “united-states” regulatory domain information;
Other changes since v6.42.6:
– backup – added support for new backup file encryption (AES128-CTR) with signatures (SHA256);
– backup – generate proper file name when devices identity is longer than 32 symbols;
– bridge – add dynamic CAP interface to tagged ports if “vlan-mode=use-tag” is enabled;
– bridge – added ingress filtering options to bridge interface;
– bridge – added initial Q-in-Q support;
– bridge – added per-port based “tag-stacking” feature;
– bridge – fixed bridge hw-offloading on MMIPS devices (introduced in v6.43rc10);
– bridge – fixed dynamic VLAN table entries when using ingress filtering;
– bridge – fixed “ingress-filtering”, “frame-types” and “tag-stacking” value storing;
– bridge – improved bridge port state changing process;
– bridge – improved packet processing when bridge port changes states;
– bridge – improved performance when bridge VLAN filtering is used without hardware offloading;
– bridge – renamed option “vlan-protocol” to “ether-type”;
– capsman – allow to change “radio-name” (CLI only);
– capsman – increase timeout for the CAP to CAPsMAN communication;
– certificate – added “expires-after” parameter;
– certificate – do not allow to perform “undo” on certificate changes;
– check-installation – improved system integrity checking;
– chr – added checksum offload support for Hyper-V installations;
– chr – added large send offload support for Hyper-V installations;
– chr – added multiqueue support on Xen installations;
– chr – added support for multiqueue feature on “virtio-net”;
– chr – added virtual Receive Side Scaling support for Hyper-V installations (might require more RAM assigned than in previous versions);
– chr – by default enable link state tracking for virtual drivers with “/interface ethernet disable-running-check=no”;
– chr – do not show IRQ entries from removed devices;
– chr – fixed interface name assign process when running CHR on Hyper-V;
– chr – fixed interface name order when “virtio-net is not being used on KVM installations;
– chr – fixed MTU changing process when running CHR on Hyper-V;
– chr – fixed NIC hotplug for “virtio-net”;
– chr – improved balooning process;
– chr – improved boot time for Hyper-V installations;
– chr – provide part of network interface GUID at the beginning of “bindstr2” value when running CHR on Hyper-V;
– chr – reduced RAM memory required per interface;
– console – do not show spare parameters on ping command;
– crs317 – fixed Ethernet inteface stuck on 100 Mbps speed;
– crs326/crs328 – fixed broken “new-dst-port” ACL rules (introduced in 6.43rc10);
– crs326/crs328 – fixed untagged packet forwarding through tagged ports when pvid=1;
– crs328 – fixed transmit on sfp-sfpplus1 and sfp-sfpplus2 interfaces;
– crs3xx – added command that forces fan detection on fan-equipped devices;
– crs3xx – added initial Q-in-Q hardware offloading support (CLI only);
– crs3xx – do not report SFP interface as running when interface on opposite side is disabled;
– crs3xx – fixed ACL rate rules (introduced in v6.41rc27);
– crs3xx – fixed flow control;
– crs3xx – fixed packet forwarding on SFP+ interfaces (introduced in v6.43rc11);
– crs3xx – fixed port disable on CRS326 and CRS328 devices;
– crs3xx – fixed tagged packet forwarding in 802.1ad aware bridges (introduced in 6.43rc13);
– crs3xx – fixed VLAN filtering when there is no tagged interface specified;
– defconf – fixed missing bridge ports after configuration reset;
– dhcp – added dynamic IPv4/IPv6 “dual-stack” simple queue support, based on client’s MAC address;
– dhcp – reduced resource usage of DHCP services;
– dhcpv4-client – fixed DHCP client that was stuck on invalid state;
– dhcpv4-client – fixed double ACK packet handling;
– dhcpv4-server – added “allow-dual-stack-queue” implementation (CLI only);
– dhcpv4-server – do not allow override lease “always-broadcast” value based on offer type;
– dhcpv4-server – fixed DHCP server functionality (introduced in v6.43rc);
– dhcpv4-server – improved performance when “rate-limit” and/or “address-list” setting is present;
– dhcpv6-client – added missing “Server identifier” parameter in release message;
– dhcpv6-client – allow to set “default-route-distance”;
– dhcpv6-client – fixed “add-default-route” parameter;
– dhcpv6-client – fixed option handling;
– dhcpv6 – improved reliability on IPv6 DHCP services;
– dhcpv6-server – added additional RADIUS parameters for Prefix delegation, “rate-limit” and “life-time”;
– dhcpv6-server – added “allow-dual-stack-queue” implementation (CLI only);
– dhcpv6-server – added initial dynamic simple queue support;
– dude – fixed client auto upgrade (broken since 6.43rc17);
– ethernet – do not show “combo-state” field if interface is not SFP or copper;
– ethernet – fixed default ethernet advertise values after configuration reset (introduced in v6.43rc33)
– ethernet – improved stability when changing ethernet interface L2MTU on CRS328-24P-4S+ (introduced in v6.43rc11);
– ethernet – properly handle Ethernet interface default configuration;
– export – do not show w60g password on “hide-sensitive” type of export;
– filesystem – fixed NAND memory going into read-only mode (requires “factory-firmware” >= 3.41.1 and “current-firmware” >= 6.43);
– filesystem – improved software crash handling on devices with FLASH type memory;
– health – fixed voltage measurements for RB493G devices;
– health – improved speed of health measurement readings;
– hotspot – allow to properly configure Hotspot directory on external disk for devices that have flash type storage;
– hotspot – fixed RADIUS CoA & PoD by allowing to accept “NAS-Port-Id”;
– ike1 – added unsafe configuration warning for main mode with pre-shared-key authentication;
– ike1 – purge both SAs when timer expires;
– ike2 – fixed rekeyed child deletion during another exchange;
– ike2 – improved basic exchange logging readability;
– ike2 – use “/32” netmask by default on initiator if not provided by responder;
– interface – improved interface “last-link-down-time” and “last-link-up-time” values;
– interface – improved reliability on dynamic interface handling;
– ipsec – added “responder” parameter for “mode-config” to allow multiple initiator configurations;
– ipsec – added “src-address-list” parameter for “mode-config” that generates dynamic “src-nat” rule (CLI only);
– ipsec – do not allow removal of “proposal” and “mode-config” entries that are in use;
– ipsec – fixed AES-CTR and AES-GCM key size proposing as initiator;
– ipsec – fixed “sa-src-address” deduction from “src-address” in tunnel mode;
– ipsec – fixed “static-dns” value storing (CLI only);
– ipsec – improved invalid policy handling when a valid policy is uninstalled;
– ipsec – improved reliability on generated policy addition when IKEv1 or IKEv2 used;
– ipsec – install all DNS server addresses provided by “mode-config” server;
– ipsec – use monotonic timer for SA lifetime check;
– kidcontrol – allow to edit discovered devices;
– ldp – properly load LDP configuration;
– led – fixed default LED configuration for RBLHGG-5acD-XL devices;
– led – improved w60g alignment trigger;
– log – fixed false log warnings about system status after power on for CRS328-4C-20S-4S+;
– log – show interface name on OSPF “different MTU” info log messages;
– lte – added additional D-Link PIDs;
– lte – added additional ID support for SIM7600 modem;
– lte – added additional low endpoint SIM7600 PIDs;
– lte – added eNB ID to info command;
– lte – added extended LTE signal info for SIM7600 modules;
– lte – added extended signal information for Quectel LTE EC25 and EP06 modem;
– lte – added ICCID reading for info command R11e-LTE and R11e-LTE-US (CLI only);
– lte – added “registration-status” parameter under “/interface lte info” command;
– lte – added roaming status reading for info command (CLI only);
– lte – added signal readings under “/interface lte scan” for 3G and GSM modes;
– lte – added support for alternative SIM7600 PID;
– lte – added support for Novatel USB730LN modem with new ID;
– lte – added support for Quanta 1k6e modem;
– lte – allow to execute concurrent internal AT commands;
– lte – allow to use multiple PLS modems at the same time;
– lte – do not allow to remove default APN profile;
– lte – do not allow to send “at-chat” commands for configless modems;
– lte – expose GPS channel for PLS modems;
– lte – fixed memory leak on USB disconnect;
– lte – fixed SIM7600 registration info;
– lte – fixed SMS send feature when not in LTE network;
– lte – ignore empty MAC addresses during Passthrough discovery phase;
– lte – improved modem event processing;
– lte – improved r11e-LTE and r11e-LTE-US dialling process;
– lte – improved r11e-LTE configuration exchange process;
– lte – improved reading of SMS message after entering running state;
– lte – improved readings of info command results for the SXT LTE;
– lte – improved stability of USB LTE interface detection process;
– lte – properly detect interface state when running for IPv6 only connection for R11e-LTE modem;
– lte – renamed LTE scan tool field “scan-code” to “mcc-mnc” (CLI only);
– lte – show UICC in correct format for SXT LTE devices;
– lte – use “/32” address for the Passthrough feature when R11e-LTE module is used;
– lte – use alphanumeric operator format in info command;
– multicast – allow to add more than one RP per IP address for PIM;
– ntp – allow to specify link-local address for NTP server;
– ospf – improved link-local LSA flooding;
– package – do not allow to install out of bundle package if it already exists within bundle;
– package – renamed “current-version” to “installed-version” under “/system package install”;
– ppp – added support for additional ID for E3531 modem;
– ppp – show comments from “/ppp secrets” menu within “/ppp active” menu when client is connected;
– quickset – recognize 160 MHz channel as HomeAP mode;
– rb1100ahx4 – added DES and 3DES hardware acceleration support;
– romon – fixed RoMON services becoming unavailable after disabled once during active scanning process;
– romon – properly classify RoMON sessions in log and active users list;
– routerboard – allow to fill up to half of the RAM memory with files on devices with FLASH storage;
– routerboard – fixed “protected-routerboot” feature (introduced in v6.42);
– routerboard – fixed wrongly reported RAM size on ARM devices;
– routerboot – removed RAM test from TILE devices (routerboot upgrade required);
– sfp – fixed DDM data with SFP+ modules on CRS328-4C-20S-4S+ (introduced in v6.43rc10);
– sfp – fixed default advertised link speeds;
– sfp – hide “sfp-wavelength” parameter for RJ45 transceivers;
– smb – fixed valid request handling when additional options are used;
– sms – converted “keep-max-sms” feature to “auto-erase”;
– sms – do not require “port” and “interface” parameters when sending SMS if already present in configuration;
– sms – improved reliability on SMS reader;
– snmp – added CAPsMAN “remote-cap” table;
– snmp – added “phy-rate” reading for “station-bridge” mode;
– snmp – fixed “remote-cap” peer MAC address format;
– ssh – disconnect all active connections when device gets rebooted or turned off;
– ssh – strengthen strong-crypto (add aes-128-ctr and disallow hmac sha1 and groups with sha1);
– supout – added “w60g” section to supout file;
– switch – added support for port isolation by switch chip;
– swos – implemented “/system swos” menu that allows to upgrade, reset, save or load configuration and change address for dual-boot CRS devices (CLI only);
– tile – added DES and 3DES hardware acceleration support;
– tr069-client – fixed setting of “DeviceInfo.ProvisioningCode” parameter;
– usb – fixed modem initialisation on LtAP mini;
– usb – fixed power-reset for hAP ac^2 devices;
– user – all passwords are now hashed and encrypted, plaintext passwords are kept for downgrade (will be removed in later upgrades);
– userman – fixed compatibility with PayPal TLS 1.2;
– vrrp – fixed VRRP packet processing on VirtualBox and VMWare hypervisors;
– vrrp – improved reliability on VRRP interface configured as a bridge port when “use-ip-firewall” is enabled;
– w60g – added distance measurement feature;
– w60g – fixed random disconnects;
– w60g – improved MCS rate detection process;
– w60g – improved MTU change handling;
– w60g – properly close connection with station on disconnect;
– watchdog – added “ping-timeout” setting;
– webfig – properly display time interval within Kid Control menu;
– webfig – properly show NTP clients “last-adjustment” value;
– winbox – added bridge Fast Forward statistics counters;
– winbox – added “poe-fault” LED trigger;
– winbox – added “secondary-channel” setting to wireless interface if 80 MHz mode is selected;
– winbox – fixed arrow key handling within table filter fields;
– winbox – fixed bridge port MAC learning parameter values;
– winbox – properly close session when uploading multiple files to the device at the same time;
– winbox – properly display all flags for bridge host entries;
– winbox – removed duplicate “20/40/80MHz” value from “channel-width” setting options;
– winbox – show HT MCS tab when “5ghz-n/ac” band is used;
– winbox – show “Switch” menu on hAP ac^2 devices;
– wireless – added option for RADIUS “called-station-id” format selection;
– wireless – do not disconnect clients when WDS master connects with MAC address “00:00:00:00:00:00”;
– wireless – fixed “/interface wireless sniffer packet print follow” output;
– wireless – fixed packet processing after removing wireless interface from CAP settings;
– wireless – fixed wireless interface lockup after period of inactivity;
– wireless – improved Nv2 reliability on ARM devices;
– wireless – improved Nv2 stability for 802.11n interfaces on RB953, hAP ac and wAP ac devices;
– wireless – updated “germany 5.8 ap” and “germany 5.8 fixed p-p” regulatory domain information;
– x86 – improved Ethernet driver for Davicom DM9x0x;
Download