MikroTik RouterOS ARM Firmware 6.43 RC 21
Tipo di file: Firmware.
Sistema Operativo: AnyOS.
Nome del file: all_packages-arm-6.43rc17.zip.
Bit: 32/64 Bit.
Licenza: Gratis.
Descrizione
MAJOR CHANGES IN v6.43:
– api – changed authentication process;
– backup – do not encrypt backup file unless password is provided;
– btest – requires at least v6.43 Bandwidth Test client when connecting to v6.43 or later version server except when authentication is not required;
– cloud – reworked “/ip cloud ddns-enabled” implementation (suggested to disable service and re-enable after installation process);
– mac-telnet – require at least v6.43 MAC Telnet client when connecting to v6.43 or later version server;
– radius – use MS-CHAPv2 for “login” service authentication;
– romon – require at least v6.43 RoMON agent when connecting to v6.43 or later RoMON client device;
– webfig – improved authentication process;
– winbox – improved authentication process excluding man-in-the-middle possibility (Winbox v3.14 required);
Modifiche in questa versione:
– dhcp – added dynamic IPv4/IPv6 “dual-stack” simple queue support, based on client’s MAC address;
– dhcp – fixed DHCP server stuck in invalid state;
– dhcpv4-server – added “allow-dual-stack-queue” implementation (CLI only);
– dhcpv6-server – added “allow-dual-stack-queue” implementation (CLI only);
– kidcontrol – added dynamic accept firewall rules in order to allow limit bandwidth when FastTrack is enabled;
– lte – do not allow to remove default APN profile;
– snmp – added “rssi” and “tx-sector-info” value support for w60g type interfaces;
– vrrp – improved reliability on VRRP interface configured as a bridge port when “use-ip-firewall” is enabled;
– w60g – added distance measurement (CLI only);
– winbox – by default specify keepalive timeout value for tunnel type interfaces;
– winbox – show “System/Health” only on boards that have health monitoring;
– wireless – added option for RADIUS “called-station-id” format selection;
– wireless – updated “germany 5.8 ap” and “germany 5.8 fixed p-p” regulatory domain information;
Other changes since v6.42.3:
– bridge – add dynamic CAP interface to tagged ports if “vlan-mode=use-tag” is enabled;
– bridge – added ingress filtering options to bridge interface (CLI only);
– bridge – added initial Q-in-Q support (CLI only);
– bridge – allow to make changes for bridge port when it is interface list;
– bridge – fixed bridge hw-offloading on MMIPS devices (introduced in v6.43rc10);
– bridge – fixed dynamic VLAN table entries when using ingress filtering;
– bridge – fixed FastPath for bridge master interfaces (introduced in v6.42);
– capsman – allow to change “radio-name” (CLI only);
– certificate – add “expires-after” parameter (CLI only);
– chr – added checksum offload support for Hyper-V installations;
– chr – added large send offload support for Hyper-V installations;
– chr – added multiqueue support on Xen installations;
– chr – added support for multiqueue feature on “virtio-net”;
– chr – added virtual Receive Side Scaling support for Hyper-V installations;
– chr – do not show IRQ entries from removed devices;
– chr – fixed adding MSTI entries;
– chr – fixed NIC hotplug for “virtio-net”;
– chr – improved boot time for Hyper-V installations;
– crs3xx – added initial Q-in-Q hardware offloading support (CLI only);
– crs3xx – fixed ACL rate rules (introduced in v6.41rc27);
– crs3xx – fixed packet forwarding on SFP+ interfaces (introduced in v6.43rc11);
– crs3xx – fixed VLAN filtering when there is no tagged interface specified;
– defconf – fixed missing bridge ports after configuration reset;
– dhcpv4-server – do not allow override lease “always-broadcast” value based on offer type;
– dhcpv4-server – fixed DHCP server functionality (introduced in v6.43rc);
– dhcpv4-server – improved performance when “rate-limit” and/or “address-list” setting is present;
– dhcpv6-client – added missing “Server identifier” parameter in release message;
– dhcpv6-server – added initial dynamic simple queue support;
– filesystem – improved software crash handling on devices with FLASH type memory;
– interface – improved reliability on dynamic interface handling;
– ipsec – added “responder” parameter for “mode-config” to allow multiple initiator configurations (CLI only);
– ipsec – added “src-address-list” parameter for “mode-config” that generates dynamic “src-nat” rule (CLI only);
– ipsec – added warning messages for incorrect peer configuration;
– ipsec – do not allow removal of “proposal” and “mode-config” entries that are in use;
– ipsec – improved reliability on generated policy addition when IKEv1 or IKEv2 used;
– ipsec – install all DNS server addresses provided by “mode-config” server;
– ipsec – separate phase1 proposal configuration from peer menu (CLI only);
– kidcontrol – allow to edit discovered devices;
– kidcontrol – fixed dynamically created firewall rules order;
– led – fixed CCR1016-12S-1S+ LED behaviour after Netinstall (introduced in v6.41rc58);
– led – improved w60g alignment trigger;
– log – show interface name on OSPF “different MTU” info log messages;
– lte – added extended LTE signal info for SIM7600 modules;
– lte – added extended signal information for Quectel LTE EC25 and EP06 modem;
– lte – added ICCID reading for info command R11e-LTE and R11e-LTE-US (CLI only);
– lte – added roaming status reading for info command (CLI only);
– lte – added support for Novatel USB730LN modem with new ID;
– lte – allow to execute concurrent internal AT commands;
– lte – allow to use multiple PLS modems at the same time;
– lte – do not allow to send “at-chat” commands for configless modems;
– lte – expose GPS channel for PLS modems;
– lte – fixed SIM7600 registration info;
– lte – improved r11e-LTE and r11e-LTE-US dialling process;
– lte – improved r11e-LTE configuration exchange process;
– lte – improved reading of SMS message after entering running state;
– lte – renamed LTE scan tool field “scan-code” to “mcc-mnc” (CLI only);
– lte – use “/32” address for the Passthrough feature when R11e-LTE module is used;
– lte – use alphanumeric operator format in info command;
– routerboard – allow to fill up to half of the RAM memory with files on devices with FLASH storage;
– routerboard – fixed “protected-routerboot” feature (introduced in v6.42);
– smb – fixed valid request handling when additional options are used;
– ssh – disconnect all active connections when router gets rebooted or turned off;
– switch – added support for port isolation by switch chip (CLI only);
– tr069-client – fixed setting of “DeviceInfo.ProvisioningCode” parameter;
– user – all passwords are now hashed and encrypted, plaintext passwords are kept for downgrade (will be removed in later upgrades);
– w60g – added 4th 802.11ad channel (CLI only);
– w60g – general stability and performance improvements;
– w60g – improved maximal achievable distance;
– w60g – removed distance lock for wAP 60G devices;
– winbox – added bridge Fast Forward statistics counters;
– winbox – fixed bridge port MAC learning parameter values;
– winbox – show “Switch” menu on hAP ac^2 devices;
– winbox – show HT MCS tab when “5ghz-n/ac” band is used;
– wireless – do not disconnect clients when WDS master connects with MAC address “00:00:00:00:00:00”;
– wireless – fixed wireless interface lockup after period of inactivity;
– wireless – improved Nv2 stability for 802.11n interfaces on RB953, hAP ac and wAP ac devices;
Download