NETGEAR PTV3000 WiDi Adapter Firmware 2.4.03
Dateityp: Firmware.
Betriebssystem: AnyOS.
Dateiname: PTV3000_V2.4.3.zip.
Bit: 32/64 Bit.
Lizenz: Kostenlos.
Beschreibung
Supported Miracast platforms:
– Samsung Galaxy S3 (Android 4.1.1 or above)
– Samsung Galaxy S4
– Samsung Galaxy Note II
– Samsung Galaxy Note 10.1
– LG Optimus G (Android 4.0.4 or above)
– Google Nexus 4 (Android 4.2.1)
– Sony Xperia (various models with Android 4.0.4 or above)
Enhancements & Bug Fixes:
– Debug mode to display additional error messages.
– Samsung Corrected User Agent to be SEC-WDH/LH01 for better Samsung TCP (movie mode) compatibility.
– Fixed an additional case that was causing the video output to fail from certain laptops.
– (Dell XPS Mod#P11F, Win7 HP x64, i7-26020M, 4GB DDR3, Centrino Advanced-N 6230 driver v15.7, HD Graphics 3000 driver v.8.15.10.2661
– P2TV3000, hardware v.2.0.0, fw v.2.3.7 Widi 4.0.18)
– Adapter name is not changed after rebooting device without disconnecting from WiDi app first.
– Overscan value was not cleared on factory reset.
– Pushbuttons now disconnect currently running sessions.
– No UI animation in connecting screen yet. It will cause UI to hang.
– Not timing out after canceling Connection from Legacy WiDi.
– Not Connecting Using WiDi 2.2 and 3.0 with FW v.2.3.7 – Only with certain laptop.
– All remaining strings translated.
– AV Sync issue vs Motorola phones. A/V interleaving has been analyzed (14515MBr12558_ENG_netgear_IHS).
– Not all audio channels have good quality. The latest Intel KPI report @ 14506 showed this as passing.
– Default overscan value set to 10. To verify this, need to reset to factory defaults first.
– Fixed issue that device displays new PIN code while PC/WiDi app is still in “connecting” state and did not come up with dialog box to allow PIN entry.
– Fixed Widi issue that device cannot connect to PC when Widi app on PC is set to speed mode.
– Enables association retry after associate reject when connection fails.
– Fixed wifi driver issue to enable disconnect event when there is no beacon from PC when PC is the GO.
– Fixed connectivity issue with Toshiba laptop when working in a noisy wifi environment.
– Fixed Widi L2SD connectivity issue.
– Change SSID to “Direct-xx-PTV” when PTV is the GO.
– Properly enables HDCP2.1 and HDCP2.0 interface.
– Fixed issue that WiDi app status shows “Connected”, device stays in “Connecting….” state forever. Timeout is enabled, worst case 2 min.
– Allow Nexus 4 to run in 2.4Ghz when Nexus 4 is not associated with any AP.
– Fixed issue of widi connection if it is right after association with Sony Xperia mobile phone.
– Fixed Widi issue that fast cursor is off by a few pixels.
– Fixed connectivity issue with BCM4352 and BCM43241 wifi controller. (Device is already compatible with Intel 11ac, N7260).
– PTV3000 didn’t get ack from invitation response but no retry to resend and the invitation response send from PTV3000 indicate failure.
– Dongle becomes unscannable after 10 hours with L2SD scan off.
– Provisional Discovery incorrectly causes PIN to be displayed.
– Nexus 4 Android 4.2.2 abruptly disconnects while streaming. Includes new QCA driver 3.2.1.122.
– [Google Nexus] RTSP UDP port seems to open successfully, but data transmission fails.
– Allow screen size adjustment on Miracast screens. See updated files in www/ (index.html and configure_overscan.sh).
– [Miracast] PTV 3000 sometimes could not be discovered at the first try.
– Inconsistency between probe response (20Mhz) and capability beaconed (20Mhz & 40Mhz) when PTV is acting as a GO.
– Throughput improved roughly 10% by disabling UDP checksum.
– Excessive frame repeats and skips [PARTIAL] #333 and #329 improve this, but needs to tested against Intel KPI.
– Support passing EDID to source unmodified.
– Fixed issue of “Push2TV” SSID not properly enabled when in FW update more. Fixed wpa_supplicant not being properly removed when switching to “Settings Mode”.
– Fixed issue with device stuck in “connecting” state forever. Another fix applied that handles a case where a failure in IP address acquisition could cause the UI to be stuck in “Connecting…”.
– Fixed the PTV not connecting with HSW+Broadcom SDIO. Adjusted default association timeout to 15 seconds from 5 seconds, as well as reduced the timeout for a scheduled scan from 5 seconds to 3 seconds. These changes fit within the timings for the source laptops times before it gives up.
– Fixed issue on connectivity with Samsung GS3. Applied patch from QCA that reduces connection retry times and checks for false PBC overlap conditions.
– Fixed provision discovery issue. Provisional Discovery incorrectly causes PIN to be displayed (partial fix). GO Negotiation with PIN is not presenting properly.
– Fixed issue that PIN pairing fails occasionally (Win Blue + 6235 WiFi).
– Fixed issue that Dongle becomes non discoverable after failed invitation attempt.
– Fixed issue that fresh pairing is inconsistent from IvyBridge+N-6235 on WiDi 4.1.17.0+15.4.1.1. Dongle tries to associate before windows blue laptop is ready for wps. This leads to connection failure.
– Fixed issue that Audio does not work with WiDi 4.x Low Delay mode.
– Fixed a number of Web UI issues.
– Change default to Auto-PBC on. (Auto-PBC and L2SD on/off can both be configured from the web UI).
– String modifications.
Download