Atomos Ninja V Recorder Firmware 10.53
Tipo di file: Firmware.
Sistema Operativo: AnyOS.
Nome del file: ATOMNJV_10.53.zip.
Bit: 32/64 Bit.
Licenza: Gratis.
Descrizione
Nota importante:
– With the installation of this update if not previously activated users will be required to activate ProRes RAW, as a codec.
– Following the Firmware update, when a RAW source is plugged in, or a user selects ProRes RAW Codec, a UI pop-up will ask for activation code to continue.
Available functions:
– SIGMA fp: Video modes available for monitoring and recording in 12 Bit RAW: 4096x2160p24, 3840×2160 up to 30p, 1920x1080p up to 119.88p
– SIGMA fp: Video modes available for monitoring and recording in 10 Bit ProRes 422 or DNx: 3840×2160 up to 30p, 1920×1080 up to 119.88p
– SIGMA fp: Monitoring of RAW input in: Native, Rec709, HLG, PQ
– SIGMA fp: Playback of recorded video in ProRes RAW, ProRes, and DNX
– FujiFilm GFX100: RAW modes available for monitoring and recording in 12 Bit RAW 3840×2160 up to 30p
– FujiFilm GFX100: Video modes available for monitoring and recording in 10 Bit ProRes 422 or DNx: 4096×2160 up to 24p, 3840×2160 up to 30p, 1920×1080 up to 60p
– FujiFilm GFX100: Monitoring of RAW input in: Native, Rec709, HLG, PQ
– FujiFilm GFX100: Playback of recorded video in ProRes RAW, ProRes 422, and DNx.
Known limitations:
– SIGMA fp: In some instances when using LUTs banding artifacts may be observed in some areas of the display on the Ninja V for 4KUHD video modes. (This behaviour is only limited to the display of the Ninja V and not the recordings).
– SIGMA fp: On occasion if the camera is. powered down whilst connect to the Ninja V and set to RAW mode, the Ninja V may enter a locked state. Switch between Record and Play back mode, Unplugging and re-plugging the HDMI, or Power cycling Switching will all resolve this issue.
– SIGMA fp: ISO metadata reported in Final Cut Pro X may occasionally be incorrect if using 1/3 EV ISO adjustments on the camera. Incorrect for camera ISO setting 1000, 8000, 16000. Update in future firmware release for camera. White balance adjustment is not available in Final Cut Pro X.
– FujiFilm GFX100: Interaction with the EVF eye sensor may cause freeze frame or black frames in the recording. Not using the EVF or tilting the LCD screen can resolve the issue. Removal of the EVF from the camera is advised to avoid issue.
– FujiFilm GFX100: White balance metadata is not reported in Final Cut Pro X. Update in future firmware release for camera and Ninja. White balance adjustment is not available in Final Cut Pro X.
– General: RAW to HDR HDMI output – PQ / HDR10 output conversion may appear slightly incorrect.
Correzioni:
– Fixed an issue where there was a chance that the display could look incorrect if switching from a RAW to YCbCr signal in ProRes RAW mode.
– Replaced YCbCR Input icon – When RAW is connected to the ninja an icon will be displayed “RAW input” if the Ninja V is set to a video codec such as ProRes or DNx. If. video signal is connected to the Ninja V when the codec is set to ProRes RAW the icon “Not RAW input” will be displayed
– DID is displayed with slashed zero to avoid typo errors when activating Apple ProRes RAW or Avid DNx.
Firmware Update Tutorial:
– Download and unzip the file.
– Copy the file onto a recommended, formatted driver, using the docking station included with your recorder.
– Insert the drive into the Atomos recorder while it’s off.
– Power up the Atomos recorder.
– The screen will show flashing lines of color. This is normal – DO NOT power off!
– Updating will take a few minutes.
– Once completed, the Atomos recorder will power down.
– Power up the Atomos recorder again.
– Check Menu > Product Info > AtomOS Version. This should match the version you have just downloaded.
– Enjoy your updated Atomos recorder !
Firmware Recovery Tutorial:
– Power down the Atomos recorder (Hold power button for 4 seconds).
– Hold down the power button for 10 seconds approximately.
– You will see the “Firmware Update Failed” screen.
– Insert your HDD / SSD.
– The install process will begin and the screen will show flashing lines of color. This is normal – DO NOT power off !
– Once completed, the Atomos recorder will power down.
– Enjoy your updated Atomos recorder !
Download