MikroTik RouterOS ARM64 Firmware 6.48 RC 35
Type de fichier: Firmware.
Système d’exploitation: AnyOS.
Nom de fichier: all_packages-arm64-6.48beta35.zip.
Bit: 32/64 Bit.
Licence: Gratuit.
Description
What’s new in 6.48beta35:
– bonding – removed “sys-id” and “sys-priority” from monitor-slaves command;
– bridge – fixed BPDU guard port disable/enable on HW offloaded interfaces;
– bridge – fixed host table update on SNMP query;
– bridge – fixed multicast table printing;
– bridge – fixed packet forwarding for CAP and BCP controlled interfaces (introduced in v6.48beta12);
– bridge – fixed STP alternate and backup port states for devices with switch chip (introduced in v6.47);
– bridge – increased multicast table size to 4K entries;
– crs3xx – fixed “mirror-source” property on switch port disable for CRS305, CRS326-24G-2S+, CRS328, CRS318 devices;
– crs3xx – fixed port isolation for “switch-cpu” port for CRS305, CRS326-24G-2S+, CRS328, CRS318 devices;
– crs3xx – fixed port isolation removal for “switch-cpu” port on CRS317, CRS309, CRS312, CRS326-24S+2Q+ and CRS354 devices;
– crs3xx – fixed “storm-rate” traffic limiting for switch-cpu port on CRS317, CRS309, CRS312, CRS326-24S+2Q+ and CRS354 devices;
– crs3xx – fixed switch ACL rules for CRS312, CRS326-24S+2Q+ and CRS354 devices;
– crs3xx – fixed switch port “egress-rate” removal for CRS305, CRS326-24G-2S+, CRS328, CRS318 devices;
– crs3xx – fixed VLAN tagged packet forwarding on “switch-cpu” port for CRS305, CRS326-24G-2S+, CRS328, CRS318 devices (introduced in v6.48beta12);
– defconf – improved CAP interface bridging;
– defconf – improved default configuration generation on devices without wireless package installed;
– discovery – added “lldp-med-net-policy-vlan” property for assigning VLAN ID (CLI only);
– discovery – allow choosing which discovery protocol is used (CLI only);
– discovery – fixed discovery on mesh ports;
– discovery – fixed discovery packet sending on newly bridged port with “protocol-mode=none”;
– discovery – fixed discovery when enabled only on master port;
– discovery – use interface MAC address when sending MNDP from slave port;
– dns – added IPv6 support for DoH;
– dns – fixed multiple TXT string replies;
– dns – hide default static entry “type” from export;
– fetch – fixed “src-address” usage for SFTP;
– filesystem – improved long-term filesystem stability and data integrity;
– health – removed unused “heater-control” and “heater-threshold” parameters;
– hotspot – added support for captive portal advertising using DHCP (RFC7710);
– hotspot – improved management service stability when receiving bogus packets;
– ike2 – fixed local side NAT detection;
– ipsec – do not kill connection when peer’s “name” or “comment” is changed;
– ipsec – refresh peer’s DNS only when phase 1 is down;
– lte – added support for Alcatel IK41VE1;
– snmp – fixed value types for “dot1dStp”;
– tr069-client – send correct “ConnectionRequestURL” when using IPv6;
– traffic-flow – added “sys-init-time” parameter support;
– wireless – allow setting “tx-power” up to 40;
Other changes since v6.47.2:
– arm – added support for automatic CPU frequency stepping for IPQ4018/IPQ4019 devices;
– arm – improved watchdog and kernel panic reporting in log after reboots on IPQ4018/IPQ4019 devices;
– bonding – added LACP monitoring (CLI only);
– bridge – added warning message when port is disabled by the BPDU guard;
– bridge – allow to exclude interfaces from extended ports (CLI only);
– bridge – correctly remove dynamic VLAN assignment for bridge ports;
– bridge – fixed dynamic VLAN assignment when changing port “frame-type” property (introduced in v6.46);
– bridge – fixed dynamic VLAN assignment when changing port to tagged VLAN member;
– bridge – fixed host table update on SNMP query;
– bridge – fixed local MAC address removal from host table when deleting bridge interface;
– bridge – improved BPDU guard logging;
– bridge – show error when switch do not support controlling bridge or port extension (CLI only);
– bridge – show “H” flag for extended bridge ports;
– certificate – clear challenge password on renew;
– chr – improved interface loading on startup on XEN;
– chr – improved system stability when changing flow control settings on e1000;
– crs3xx – added initial Bridge Port Extender support (CLI only);
– crs3xx – added initial Controlling Bridge support for CRS317, CRS309, CRS312, CRS326-24S+2Q+ and CRS354 devices (CLI only);
– crs3xx – fixed “custom-drop-packet” and “not-learned” switch stats for CRS317, CRS309, CRS312, CRS326-24S+2Q+ and CRS354 devices;
– crs3xx – fixed duplicate host entries when creating static switch hosts;
– crs3xx – fixed hardware offloaded MPLS forwarding when using bonding interfaces;
– crs3xx – fixed switch “not-learned” stats for CRS305, CRS326-24G-2S+, CRS328-24P-4S+, CRS328-4C-20S-4S+, CRS318 devices;
– crs3xx – improved Ethernet port group traffic forwarding for CRS354 devices;
– crs3xx – improved system stability when using hardware offloaded MPLS;
– defconf – improved default configuration generation on devices with non-default wireless interface names;
– dhcpv6-server – added ability to generate binding on first request;
– discovery – send the same “Chassis ID” on all interfaces for LLDP packets;
– dns – do not use type “A” for static entries with unspecified type;
– dns – fixed listening for DNS queries when only dynamic static entries exist (introduced in v6.47);
– dot1x – fixed duplicate EAP request packets for server;
– dot1x – fixed EAP packet version numbering;
– export – fixed RouterBOARD USB “type” parameter export;
– filesystem – fixed repartition on non-first partition;
– filesystem – fixed repartition on RB4011 series devices;
– filesystem – improved long-term filesystem stability and data integrity;
– gps – fixed “init-channel” release when not used;
– health – changed PSU state parameter type to read-only;
– health – removed unused “heater-control” and “heater-threshold” parameters;
– hotspot – added “vlan-id” parameter support for hosts and HTML pages;
– hotspot – ignore packets from host while MAC authentication is in progress;
– ike1 – allow using “my-id” parameter with XAuth;
– ike1 – fixed policy update with and without mode configuration;
– ike1 – rekey phase 1 as responder for Windows initiators;
– ike2 – added “prf-algorithm” support for phase 1;
– ike2 – improved child SA rekeying process;
– ipsec – added SHA384 hash algorithm support for phase 1 (CLI only);
– ipsec – fixed client certificate usage when certificate is renewed with SCEP;
– ipsec – fixed multiple warning message display for peers;
– ipsec – inactivate peer’s policy on disconnect;
– kidcontrol – allow creating static device entries without assigned user;
– kidcontrol – fixed “time-unlimited-rate” to engage in correct time;
– lora – expose “joinEui” un “devEui” values in the log;
– lte – added “age” column and “max-age” parameter to “cell-monitor” (CLI only);
– lte – added “comment” parameter for APN profiles;
– lte – added “comment” parameter for APN profiles (CLI only);
– lte – fixed multiple passthrough APN default route installation;
– lte – fixed RSCP value reporting;
– lte – validate interface existence on initiation;
– ospf – fixed disappearing NSSA default route;
– ospf – fixed processing of “unknown” LSA type;
– ospf – optimized LSA printing for smaller message sizes;
– poe – fixed “power-cycle” functionality on RB960GSP;
– ppp – added “ipv6-routes” parameter to “secrets” menu;
– ppp – added support for “Framed-IPv6-Route” RADIUS attribute;
– route – improved stability when 6to4 interface is configured with disabled IPv6 package;
– routerboot – fixed etherboot FCS errors with 100Mbps rate for CRS309, CRS317 devices (“/system routerboard upgrade” required);
– ssh – fixed returned output saving to file when “output-to-file” parameter is used;
– ssh – skip interactive authentication when not running in interactive mode;
– system – replace “3” in superscript to “^3” on RBD53GR devices;
– tr069-client – added additional wireless registration table parameters;
– tr069-client – added LTE model and revision parameters;
– tr069-client – added wireless “noise-floor” and “overall-tx-ccq” information parameters;
– tr069-client – added “X_MIKROTIK_MimoRSRP” parameter for LTE RSRP value reporting;
– tr069-client – allow passing LTE firmware update URL as XML;
– traffic-flow – added NAT event logging support for IPFIX;
– webfig – fixed default value presence when creating new entries under “IP->Kid Control”;
– webfig – fixed negative value usage in “spoof-gps” parameter (introduced in v6.47.1);
– winbox – allow performing “USB Power Reset” on “0” bus on RBM33G;
– winbox – fixed “IP->Kid Control->Devices” table automatic refreshing;
– winbox – fixed minor typo in “Users” menu;
– winbox – fixed “receive-errors” setting persistence under “Wireless/Wireless Sniffer/Settings” menu;
– winbox – fixed “tls-version” parameter setting under “IP/Services” menu;
– winbox – use health values reported by gauges for “System/Health” menu;
– wireless – added support for U-NII-2 for wAP ac;
– wireless – create “connect-list” rule when address specified for “setup-repeater”;
– wireless – updated “canada” regulatory domain information;
– wireless – updated “no_country_set” regulatory domain information;
– wireless – updated “united states” regulatory domain information;
Télécharger