Fujifilm X-Pro2 Camera Firmware 3.00
Type de fichier: Firmware.
Système d’exploitation: AnyOS.
Nom de fichier: FWUP0008.DAT.
Bit: 32/64 Bit.
Licence: Gratuit.
Description
Changements:
– “Voice memo” function added
– “Copyright information” function added
– Improved operability of AF / movie shooting / viewfinder etc.
The firmware update Ver.3.00 from Ver.2.10 incorporates the following issues:
1. Shooting RAW in Bracketing and Advanced Filters
The update enables you to use the RAW format when shooting not only in AE Bracketing but also in other Bracketing modes (ISO, Dynamic Range, White Balance, Film Simulations) and also in Advanced Filter modes.
2. Extended ISO 125 and 160 selectable
The update adds ISO125 and ISO160 to extended ISO levels available.
3. Programmable long exposure of up to 15 minutes
Long exposure in the T mode currently goes only up to 30 seconds. The update will allow users to extend it up to 15 minutes.
4. “AUTO” setting added for the minimum shutter speed in the ISO Auto setting
The update adds an AUTO option for the minimum shutter speed in the ISO Auto setting, that allows the camera to automatically define the minimum shutter speed according to the focal length of the lens attached.
5. Faster “Face Detection AF”
The update enables the use of Phase Detection AF for faster performance in Face Detection AF.
6. Improved in-focus indication in the AF-C mode
The update reduces focus hunting in the AF-C mode, making it easier to track a subject.
7. Addition of a smaller Focus Point size in Single Point AF
The update adds a smaller Focus Point size in Single Point AF, bringing the total number of available sizes to six. The new smallest size facilitates pin-point focusing.
8. Addition of “AF Point Display”
With the update, you can choose to have AF Points constantly displayed in Zone AF and Wide / Tracking AF, making it easier to track a subject.
[How to set]
AF/MFSETTING>AF POINT DISPLAY
9. Addition of “AF-C Custom Setting”
The update adds “AF-C Custom Setting” for specifying focus-tracking characteristics. Choose from five presets according to your subject’s type of movements.
[How to set]
AF-C CUSTOM SETTING
10. Change of focus frame position while enlarging it
The update allows you to move the position of focus frame while enlarging it in Single Point in the AF-S mode or in the Manual Focus.
11. Addition of “Eye Sensor + LCD Image Display” in the View Mode
The update gives the “Eye Sensor + LCD Image Display” option in the View Mode that allows you to shoot through the viewfinder and check images on the LCD, just as you would with an SLR.
12. Shorter EVF display time-lag
The update shortens EVF display time-lag in the AF-C mode so that you will not miss a photo opportunity.
13. Name Custom Settings
The update allows you to assign a specific name to Custom Settings 1 – 7.
[How to set]
IMAGE QUALITY SETTING>EDIT/SAVE CUSTOM SETTING>CUSTOM1-7>EDIT CUSTOM NAME
14. Copyright information in EXIF data
The update allows you to register the photographer’s name and the copyright holder’s name in advance so that the camera automatically adds the information to EXIF data for each image.
[How to set]
SET UP>SAVE DATA SET-UP>COPYRIGHT INFO
15. Voice Memo function
The update enables you to record 30-second “Voice Memo” clips in the Playback mode.
[How to set]
PLAY BACK MENU>VOICE MEMO SETTING>ON
When recorded images are displayed, press the front command dial for a while to start memo recording. When you remove your finger from the dial, it stops.
16. Extended AE Bracketing
The update extends AE Bracketing from the current 3 frames +/-2EV to up to 9 frames +/-3EV.
17. Addition of “Shoot Without Card” mode
With the update, you can have the “Shoot Without Card” mode turned OFF so that the camera cannot shoot when there is no SD card inserted.
[How to set]
SET UP>BUTTON/DIAL SETTING>SHOOT WITHOUT CARD
Précautions:
– Si la mise à jour du micrologiciel échoue, la caméra risque de ne plus fonctionner correctement dans certains cas. Carefully read the notes provided here.
– Utilisez toujours la batterie complètement chargée lors de la mise à jour du firmware de manière basique. Ne mettez jamais l’appareil photo hors tension et n’essayez jamais d’utiliser les commandes de l’appareil photo lorsque le micrologiciel est écrasé.
– La mise à jour du micrologiciel nécessite environ 90 secondes.
– Une fois le firmware mis à jour, certaines données de la version précédente ne peuvent plus être restaurées.
– Please check here if you encounter any problems.
Instructions d’installation:
– Placez la carte mémoire formatée dans un lecteur de carte de votre PC / Mac.
– Téléchargez le firmware
– Copiez le fichier téléchargé sur la carte.
– Retirez la carte de la fente du lecteur de cartes une fois la copie terminée et déposez-la dans l’appareil photo.
– Utilisez une batterie complètement chargée. Si l’appareil photo s’éteint pendant la mise à jour du micrologiciel, cela ne fonctionnera pas bien.
– La durée de la mise à jour du micrologiciel varie en fonction de la capacité du micrologiciel, mais elle est d’env. 90 sec. Ne mettez jamais l’appareil photo hors tension et ne l’utilisez pas pendant la mise à jour du firmware.
– Allumez l’appareil photo en appuyant sur la touche “DISP / BACK” pour afficher l’écran à droite. Appuyez ensuite sur la touche “MENU / OK”
– Après avoir confirmé l’élément en tant que [CORPS] pour mettre à jour le boîtier de l’appareil photo, appuyez sur le bouton [OK].
– Appuyez sur le bouton [OK] pour passer à l’étape suivante.
– Appuyez sur la touche [UP] pour sélectionner “OK”.
– Appuyez sur le bouton [OK].
– La mise à jour du micrologiciel est lancée.
– La mise à jour du firmware prend environ 90 secondes.
– Lorsque cet écran apparaît, la mise à jour du firmware a été complétée avec succès.
– Mettez l’appareil photo hors tension.
– Vérifiez le micrologiciel mis à niveau.
– En suivant la procédure ci-dessus “Procédure de vérification de la version du firmware”, vous pouvez voir la version du firmware.
– Format the card.
Télécharger