Fujifilm X-Pro2 Camera Firmware 3.00
Tipo de archivo: Firmware.
Sistema Operativo: AnyOS.
Nombre del archivo: FWUP0008.DAT.
Bit: 32/64 Bit.
Licencia: Gratuito.
Descripción
Cambios:
– “Voice memo” function added
– “Copyright information” function added
– Improved operability of AF / movie shooting / viewfinder etc.
The firmware update Ver.3.00 from Ver.2.10 incorporates the following issues:
1. Shooting RAW in Bracketing and Advanced Filters
The update enables you to use the RAW format when shooting not only in AE Bracketing but also in other Bracketing modes (ISO, Dynamic Range, White Balance, Film Simulations) and also in Advanced Filter modes.
2. Extended ISO 125 and 160 selectable
The update adds ISO125 and ISO160 to extended ISO levels available.
3. Programmable long exposure of up to 15 minutes
Long exposure in the T mode currently goes only up to 30 seconds. The update will allow users to extend it up to 15 minutes.
4. “AUTO” setting added for the minimum shutter speed in the ISO Auto setting
The update adds an AUTO option for the minimum shutter speed in the ISO Auto setting, that allows the camera to automatically define the minimum shutter speed according to the focal length of the lens attached.
5. Faster “Face Detection AF”
The update enables the use of Phase Detection AF for faster performance in Face Detection AF.
6. Improved in-focus indication in the AF-C mode
The update reduces focus hunting in the AF-C mode, making it easier to track a subject.
7. Addition of a smaller Focus Point size in Single Point AF
The update adds a smaller Focus Point size in Single Point AF, bringing the total number of available sizes to six. The new smallest size facilitates pin-point focusing.
8. Addition of “AF Point Display”
With the update, you can choose to have AF Points constantly displayed in Zone AF and Wide / Tracking AF, making it easier to track a subject.
[How to set]
AF/MFSETTING>AF POINT DISPLAY
9. Addition of “AF-C Custom Setting”
The update adds “AF-C Custom Setting” for specifying focus-tracking characteristics. Choose from five presets according to your subject’s type of movements.
[How to set]
AF-C CUSTOM SETTING
10. Change of focus frame position while enlarging it
The update allows you to move the position of focus frame while enlarging it in Single Point in the AF-S mode or in the Manual Focus.
11. Addition of “Eye Sensor + LCD Image Display” in the View Mode
The update gives the “Eye Sensor + LCD Image Display” option in the View Mode that allows you to shoot through the viewfinder and check images on the LCD, just as you would with an SLR.
12. Shorter EVF display time-lag
The update shortens EVF display time-lag in the AF-C mode so that you will not miss a photo opportunity.
13. Name Custom Settings
The update allows you to assign a specific name to Custom Settings 1 – 7.
[How to set]
IMAGE QUALITY SETTING>EDIT/SAVE CUSTOM SETTING>CUSTOM1-7>EDIT CUSTOM NAME
14. Copyright information in EXIF data
The update allows you to register the photographer’s name and the copyright holder’s name in advance so that the camera automatically adds the information to EXIF data for each image.
[How to set]
SET UP>SAVE DATA SET-UP>COPYRIGHT INFO
15. Voice Memo function
The update enables you to record 30-second “Voice Memo” clips in the Playback mode.
[How to set]
PLAY BACK MENU>VOICE MEMO SETTING>ON
When recorded images are displayed, press the front command dial for a while to start memo recording. When you remove your finger from the dial, it stops.
16. Extended AE Bracketing
The update extends AE Bracketing from the current 3 frames +/-2EV to up to 9 frames +/-3EV.
17. Addition of “Shoot Without Card” mode
With the update, you can have the “Shoot Without Card” mode turned OFF so that the camera cannot shoot when there is no SD card inserted.
[How to set]
SET UP>BUTTON/DIAL SETTING>SHOOT WITHOUT CARD
Precauciones
– Si falla la actualización del firmware, es posible que la cámara ya no funcione correctamente en algunos casos. Carefully read the notes provided here.
– Use siempre la batería completamente cargada cuando actualice el firmware de manera básica. Nunca apague la cámara ni intente utilizar ninguno de los controles de la cámara mientras se sobrescribe el firmware.
– La actualización del firmware requiere aproximadamente 90 segundos.
– Una vez que el firmware se ha actualizado, algunos datos de la versión anterior no se pueden restaurar.
– Please check here if you encounter any problems.
Instrucciones de instalación:
– Coloque la tarjeta de memoria formateada en una ranura de lector de tarjetas de su PC / Mac.
– Descargue el firmware
– Copie el archivo descargado a la tarjeta.
– Tome la tarjeta de la ranura del lector de tarjetas después de que se complete la copia y colóquela en la cámara.
– Use una batería completamente cargada. Si la cámara se apaga durante la actualización del firmware, no funcionará bien.
– El tiempo de actualización del firmware varía según la capacidad del firmware, pero es de aprox. 90 seg. Nunca apague la cámara y opérela durante la actualización del firmware.
– Encienda la cámara presionando el botón “DISP / BACK” para mostrar la pantalla a la derecha. Luego, presione el botón “MENÚ / OK”
– Después de confirmar el elemento como [CUERPO] para actualizar el cuerpo de la cámara, presione el botón [OK].
– Presione el botón [OK] para ir al siguiente paso.
– Presione el botón [ARRIBA] para seleccionar “OK”.
– Presione el botón [OK].
– Se inicia la actualización del firmware.
– La actualización del firmware tarda aproximadamente 90 segundos.
– Cuando aparece esta pantalla, la actualización del firmware se ha completado con éxito.
– Apague la cámara.
– Verifique el firmware actualizado.
– Siguiendo el procedimiento anterior “Procedimiento de verificación de la versión del firmware”, puede ver la versión del firmware.
– Format the card.
Descargar