MikroTik RouterOS SMIPS Firmware 6.39 RC 62
Dateityp: Firmware.
Betriebssystem: AnyOS.
Dateiname: routeros-smips-6.39rc62.npk.
Bit: 32/64 Bit.
Lizenz: Kostenlos.
Beschreibung
What’s new in 6.39rc62:
– firewall – discontinued support for p2p matcher (old rules will become invalid);
– capsman – added “extension-channel” XX and XXXX auto matching modes;
– capsman – added “keepalive-frames” setting;
– capsman – added “skip-dfs-channels” setting;
– capsman – added ability to specify multiple channels in frequency field;
– capsman – added DFS support;
– capsman – added support for “background-scan” and channel “reselect-interval”;
– capsman – changed channel “width” name to “control-channel-width” and changed default values;
– fastpath – fixed rare crash on devices with dynamic interfaces;
– smips – reduced RouterOS main package size;
– tile – optimized hardware encryption;
– tr069-client – added firewall NAT support using vendor Parameters;
– tr069-client – added support for uploading/downloading factory script;
– webfig – correctly specify routing filter prefix;
– winbox – allow to specify “route-distance” in “dhcp-client” if “special-classless” mode is selected;
– winbox – do not allow Packet Sniffer “memory-limit” lower than 10KiB;
– winbox – fixed “Montly” typo to “Monthly” in Graphing menu;
– winbox – hide health menu on RB450;
– winbox – properly show “dhcp-server” warnings;
– winbox – properly show IPSec “installed-sa” “enc-algorithm” when it is aes-gcm;
– winbox – set default “dhcp-client” “default-route-distance” value to 1;
– winbox – show PoE-OUT current, voltage and power only on devices which can report these values;
– wireless – added PEAP authentication support for wireless station mode;
Other changes since 6.38.5:
– bridge – added “fast-forward” setting and counters (enabled by default only for new bridges) (CLI only);
– bridge – added support for special and faster case of fastpath called “fast-forward” (available only on bridges with 2 interfaces);
– bridge – fixed BPDU rx/tx when protocol-mode=none;
– filesystem – fixed rare situation when filesystem failed to read all configuration on startup;
– filesystem – fixed rare situation when filesystem went into read-only mode (some configuration might have gotten lost on reboot);
– l2tp – added fastpath support when MRRU is enabled;
– ppp – completely rewritten internal fragmentation algorithm (when MRRU is used), optimized for multicore;
– ppp – implemented internal algorithm for “change-mss”, no mangle rules necessary;
– pppoe – added fastpath support when MRRU and MLPPP are enabled;
– quickset – configuration changes are now applied only on “OK” and “Apply” (not on mode change);
– tile – fixed IPsec hardware acceleration out-of-order packet problem, significantly improved performance;
– winbox – minimal required version is v3.11;
– address – fixed crash when address is assigned to another bridge port;
– api – fixed double dynamic flags for “/ip firewall address-list print”;
– capsman – added CAP discovery interface list support;
– capsman – added save-channel option to speed up frequency selection on CAPsMAN restart;
– capsman – added support for static virtual interfaces on CAP;
– capsman – improved CAP status querying;
– capsman – improved support for communicating frame priority between CAP and CAPsMAN;
– certificate – allow CRL address to be specified as DNS name;
– certificate – SCEP client now supports FQDN URL and port;
– console – fixed “/ip neighbor discovery” export;
– console – fixed crash;
– console – fixed DHCP/PPP add-default-route distance minimal value to 1;
– console – fixed incorrect “:put [/lcd get enabled]” value;
– defconf – fixed default configuration generation when wireless package is disabled;
– defconf – fixed Groove 52 ac band settings;
– dhcp-client – added “script” option which executes script on state changes;
– dhcpv4-server – added “lease-hostname” script parameter;
– dhcpv4-server – by default make server “authoritative”;
– dhcpv4-server – do some lease checks only on enabled object;
– email – check for errors during SMTP exchange process;
– ethernet – added “voltage-too-low” status for single port power injector devices;
– ethernet – fixed “loop-protect” on “master-port”;
– ethernet – fixed rare switch chip hang (could cause port flapping);
– ethernet – fixed unnecessary power cycle of powered device when changing any poe-out related setting on single port power injector devices;
– ethernet – renamed “rx-lose” to “rx-loss” in ethernet statistics;
– ethernet – reversed poe-priority on hEX PoE and OmniTIK 5 PoE to make “poe-priority” consistent to all other RouterOS priorities;
– fetch – added “http-data” and “http-method” parameters to allow delete, get, post, put methods (content-type=application/x-www-form-urlencoded by default);
– gps – added “fix-quality” and “horizontal-dilution” parameters;
– graphing – fixed graph disappearance after power outage;
– hotspot – added access to HTTP headers using $(http-header-name);
– ike1 – fixed ph2 ID logging;
– ike2 – always replace empty TSi with configured address if it is available;
– ike2 – check child state before allowing rekey;
– ike2 – default to /32 peer address mask;
– ike2 – fixed CTR mode;
– ike2 – fixed ctr mode;
– ike2 – fixed EAP message length;
– ike2 – fixed ISA handler object removal on SA delete;
– ike2 – fixed ph2 state when sending notify;
– ike2 – fixed state when sending delete packet;
– ike2 – remove old SA after rekey;
– ike2 – send EAP identity as user-name RADIUS attribute;
– ike2 – update “calling_station_id” radius attribute;
– ike2 – update peer identity after successful EAP authentication;
– ippool – return proper error message when trying to create duplicate name;
– ipsec – added “last-seen” parameter to active connection list;
– ipsec – allow mixing aead algorithms in proposal;
– ipsec – better responder flag calculator for console;
– ipsec – enable aes-ni on i386 and x64 for cbc, ctr and gcm modes;
– ipsec – fixed “/ip ipsec policy group export verbose”;
– ipsec – fixed “mode-cfg” verbose export;
– ipsec – fixed SA authentication flag;
– ipsec – renamed “hw-authenc” flag to “hw-aead”;
– ipsec – show hardware accelerated authenticated SAs;
– ipsec – updated tilera classifier for UDP encapsulated ESP;
– l2tp-server – added “use-ipsec=required” option;
– leds – added LTE modem access technology trigger;
– leds – changed error message on unsupported board;
– leds – do not update single LED state when it is not changed;
– leds – show warning on print when “modem-signal-threshold” is not available;
– log – added “gps” topic;
– log – added “tr069” topic;
– log – added warning when Winbox/Dude sessions were denied;
– log – do not show changes in packet if NAT has not been used;
– log – make SNMP logs more compact;
– lte – added error handling for remote AT execute;
– lte – added initial support for Quectel ec25;
– lte – added initialization for Cinterion;
– lte – added log entry for SMS delivery report;
– lte – added LTE signal level reading for Cinterion modems;
– lte – added support for Vodafone R216 (Huawei);
– lte – buffer AT events while info command is active;
– lte – fixed “/interface lte info X once”;
– lte – fixed IPv6 address prefix on interface
– lte – fixed network mode selection for me909u, mu609;
– lte – fixed older standard CEREG parsing;
– lte – fixed support for Huawai R216;
– lte – fixed user-command;
– netinstall – fixed typos;
– ntp – restart NTP client when it is stuck in error state;
– ppp – fixed rare kernel failure on PPP client connection;
– ppp-client – added support for Datacard 750UL, DWR-730 and K4607-Zr;
– pppoe – set default keepalive 10s for newly created PPPoE clients;
– rb1100ahx2 – fixed random counter resets for ether12,13;
– rb3011 – added partitioning support;
– smb – fixed different memory leaks and crashes;
– smb – fixed share path on devices with “/flash” directory;
– snmp – “No Such Instance” error message is replaced with “No Such Object”;
– snmp – added fan-speed OIDs in “/system health print oid”;
– snmp – added optical table;
– snmp – fixed rare crash;
– snmp – improved getall filter;
– snmp – improved response speed when multiple requests are received within short period of time;
– snmp – optimized bridge table processing;
– tile – added initial support for NVMe SSD disk drives;
– tr069-client – added “Device.Hosts.Host.{i
Download